Panasonic AJ-HPM200E Скачать руководство пользователя

Страница: 182 / 230

182

Setup: Item Settings

505

TCG REGEN

0000

0001

0002

TC&UB

Specifies the signal to regenerate when the time code generator (TCG) is in the REGEN

mode.

0: Regenerates both the time code and the user bit

1: Regenerates only the time code

2: Regenerates only the user bit

507

EXT TC SEL

0000

0001

0002

EXT_L

SLTC

SVITC

Specifies the time code used when an external time code is used.

0: LTC of the TIME CODE IN connector

1: LTC data attached to serial signal input to HD SDI IN

2: VITC data attached to serial signal input to HD SDI IN

NOTE:

When SLTC and SVITC are set, the VITC in the input video signal is used when an

analog composite or SD SDI input signal is selected. When 1394 is selected as the

input signal, the IEEE 1394 digital input signal time code is used regardless of this

setting.

508

BINARY GP

0000

0001

0002

0003

0004

0005

0006

0007

000

001

010

011

100

101

110

111

Specifies user bit usage in time code generated by the TCG.

0: NOT SPECIFIED (character set not specified)

1: ISO CHARACTER (8-bit character set complying with ISO646 and ISO2022)

2: UNASSIGNED 1 (undefined)

3: UNASSIGNED 2 (undefined)

4: UNASSIGNED 3 (undefined)

5: PAGE/LINE

6: UNASSIGNED 4 (undefined)

7: UNASSIGNED 5 (undefined)

509

PHASE CORR

0000

0001

OFF

Specifies whether or not LTC output from the TIME CODE OUT connector should be

phase controlled.

0: No phase control

1: Phase controlled

510

TCG CF FLAG

0000

0001

OFF

Sets the TCG CF flag.

0: OFF

1: ON

511

DF MODE

0000

0001

NDF

Sets the DF or NDF mode for CTL and TCG.

0: Uses drop frame mode.

1: Uses non-drop frame mode.

512

TC OUT REF

0000

0001

VOUT

TC_IN

Specifies how the phase is switched for the time code output by the TIME CODE OUT

connector for the external LTC input when the TC INT/EXT switch is set to EXT. (only in EE

mode)

0: Synchronized with output video signal.

1: Synchronized with the external time code input.

513

VITC OUT

0000

0001

SBC

VAUX

Specifies how to output VITC that will be superimposed on the SD output video signal.

0: Outputs the time code recorded in the SBC area as VITC

1: Outputs the time code recorded in the VAUX area as VITC

NOTE:

VITC data detected in the input video signal is automatically recorded in the VAUX area

during video recording.

Item

Setting

Settings and brief function description

No.

SUPER

DISP.

No.

SUPER

DISP.

59.94Hz

50Hz

23.98Hz

24Hz

29.97Hz

25Hz

only

59.94Hz

50Hz

23.98Hz

24Hz

29.97Hz

25Hz

only

59.94Hz

50Hz

29.97Hz

25Hz

60-25Hz

only

59.94Hz

29.97Hz

only

59.94Hz

50Hz

23.98Hz

24Hz

29.97Hz

25Hz

only

Содержание AJ-HPM200E







































































































































































































































Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200E, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды