Panasonic AJ-HPM200E Скачать руководство пользователя страница 178

Страница: 178 / 230

178

Setup: Item Settings

148

WFM POS.

0000

0001

0002

0003

Selects the position for the waveform monitor.

0: Top right

1: Top left

2: Bottom right

3: Bottom left

155

AUTO REC

0000

0001

0002

0003

OFF

TYPE1

TYPE2

TYPE3

Select whether recording and stopping should be performed automatically according to

the recording/stopping signals in the HD SDI input signals from Panasonic camera-

recorders.

0: No automatic recording/stopping

1: Recording and stopping is performed automatically according to the recording/

stopping signals in the LTC information attached to HD SDI signals.

2: Recording and stopping is performed automatically according to the recording/

stopping signals in the SVITC information attached to HD SDI signals.

3: Set when other manufacturer's camera-recorders are used.

NOTE:

• When the thumbnail screen or playlist screen is displayed, this setting is disabled and

has no effect.

• Set the CONTROL switch to REMOTE.

Refer to “Panasonic camera-recorders, recording formats and recording/stopping

signals (Recording Mark)” (page 179) before selecting TYPE1 or TYPE2.

• To start automatic recording, press the REC and STILL buttons simultaneously to

place this unit in REC PAUSE mode. Automatic recording does not start any mode

other than REC PAUSE mode. The unit returns to REC PAUSE mode when automatic

stop is activated.

• In normal recording mode, this setting is not available and auto stop is not activated.

• For the devices verified as TYPE3 devices, visit the following Web site:

For English: http://panasonic.biz/sav/autorec_e

160

REPEAT PLAY

0000

0001

OFF

Determines whether or not to engage repeat play during playback.

0: Does not engage repeat play. Stops playback at the end of the last clip.

1: Engages repeat play. Continues playback from the beginning when reaching the end

of the last clip.

NOTE:

• Repeat play is not available when the PLAYLIST button is on and during TEXT MEMO

playback.

• If the P2 card is removed during repeat play, playback is suspended when playback

reaches the clip that is no longer exists.

• Even if you insert a P2 card during repeat play, additional clips are not played back

until you once stop repeat play and resume it.

• Always OFF when setup menu No. 27 (VDCP CMD) is ON.

165

CLIPSEL MODE

0000

0001

TOP

THUMB

Selects position of clip displayed by clip select.

0: Uses the first frame of the clip to select clips.

1: Uses clip thumbnail position to select clips.

NOTE:

This is a setting for control from the REMOTE connector.

Item

Setting

Settings and brief function description

No.

SUPER

DISP.

No.

SUPER

DISP.

59.94Hz

50Hz

only

Содержание AJ-HPM200E







































































































































































































































Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200E, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды