Panasonic AJ-HPM200E Скачать руководство пользователя

Страница: 187 / 230

Setup: Item Settings

187

S
e

677

LCD ASPECT

0000

0001

0002

0003

AUTO

4:3

16:9

15:9

Specifies the aspect ratio of image displayed on the LCD monitor.

0: Switches aspect ratio automatically.

1: Displays 480i or 576i images in the 4:3 aspect ratio.

(Displays 1080i or 720p video in the 16:9 aspect ratio.)

2: Displays images in the 16:9 aspect ratio.

3: Displays images in the 15:9 aspect ratio.

NOTE:

Since the LCD monitor on this unit has an aspect ratio of 15:9, a black border may

appear above and below the picture in AUTO or 16:9 mode.

680

CC (F1) BLANK

0000

0001

BLANK

THRU

Turns on and off closed caption signals in the first field output from the SD SDI and analog

composite output.

0: Signals are forcibly blanked.

1: Signals are not blanked.

NOTE:

In EE mode, the closed captions are output superimposed on the input signal.

681

CC (F2) BLANK

0000

0001

BLANK

THRU

Turns on and off closed caption signals in the second field output from the SD SDI and

analog composite output during playback.

0: Signals are forcibly blanked.

1: Signals are not blanked.

NOTE:

In EE mode, the closed captions are output superimposed on the input signal.

684

EDH(SD)

0000

0001

OFF

Specifies whether or not EDH is superimposed on SDI OUT signals.

0: Signals are not superimposed.

1: Signals are superimposed.

685

ESR MODE(SD)

0000

0001

OFF

AUTO

Specifies the operating mode for edge subcarrier reduction (ESR) in the playback circuit.

0: ESR is forcibly set to off.

1: ESR is automatically turned on and off depending on operating mode.

688

CC REC

0000

0001

OFF

Specifies whether or not the closed caption signal that is superimposed on the SD SDI

and analog composite input signals will be recorded.

0: Not recorded.

The EE output is also blanked.

1: A closed caption signal that is superimposed on an input signal is recorded.

NOTE:

When 1394 is selected as the input signal, the closed caption signal superimposed on

the compressed input signal is recorded in its original form regardless of settings in this

menu.

689

COMP MODE

0000

0001

NORMAL

DARK

Selects the compression method used during video recording.

0: Records using normal compression processing.

1: Records video suppressing compression video distortion that is generated by dark

areas that are about 10 IRE (70 mV) or less.

NOTE:

This setting is available in DVCPRO HD 720p mode recording.

690

UMID REC

0000

0001

OFF

Specifies whether or not UMID data should be recorded.

0: UMID data is not recorded.

1: Recorded.

Item

Setting

Settings and brief function description

No.

SUPER

DISP.

No.

SUPER

DISP.

59.94Hz

only

59.94Hz

only

59.94Hz

50Hz

29.97Hz

25Hz

60-25Hz

only

59.94Hz

29.97Hz

only

59.94Hz

only

59.94Hz

50Hz

29.97Hz

59-23Hz

60-24Hz

25Hz

60-25Hz

only

Содержание AJ-HPM200E







































































































































































































































Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200E, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды