Panasonic AJ-HPM200E Скачать руководство пользователя страница 126

Страница: 126 / 230

126

Connections: Using This Unit With a Hard Disk

Follow the steps below to initialize a hard disk in a TYPE S or

FAT format.

◆

NOTE:

• Note that formatting a hard disk deletes all data on the disk.

Press the THUMBNAIL button.

Connect a USB or eSATA hard disk.

Hard disk status (page 49) changes to white (or red) when

a hard disk is recognized.

Press the MENU button.

Use the cursor buttons to select [HDD (USB or

eSATA)] – [EXPLORE] and press the SET button.

The explorer screen will now open.

Press the MENU button, use the cursor buttons to

choose [OPERATION] – [FORMAT (HDD)] and

press the SET button. Then select the format (TYPE

S or FAT) and press the SET button.

Select [YES] in the confirmation message that

appears and press the SET button.

When the confirmation message appears again,

select [YES] and press the SET button.

The hard disk will now be formatted.

◆

NOTE:

• Check that no important data remains on the hard disk before

formatting since data erased by formatting cannot be

recovered.

This unit provides high-speed export (writing data from a P2

card to a hard disk) of data from a P2 card to a hard disk. The

copy result and and the maximum number of copies differ,

depending on the hard disk format type.

Folders are created in two levels: date (year/month/date), and time

(hour/minute/second).

Example of 12:34:56 on March 30 of 2010

10-03-30/12-34-56

Copy volume is limited by the capacity of the storage device.

Formatting Hard Disks

OFF

METER

FULL/FINE

MONITOR

SELECT

METER SELECT

INPUT SELECT

REC

THUMBNAIL

SET

MENU

ENTRY

SLOT CLIP

PF1

ALL CLIP

PF3

SHIFT

PF4

CLIP LIST

PF2

SLOT SELECT

LAST X

TRIM

DELETE

VIDEO

PLAYLIST

GO TO

OUT

EDIT MODE

A.DUB
MODE

DIAG

OPERATION

EXIT

CANCEL/PF

MULTI

SEL

CH 1

CH 2

CH 3

CH 4

TEXT

MEMO

TCG

TC PRESET

PROP

RESET

COUNTER

PLAYER

STOP

STILL/

PAUSE

PREVIEW

A.LEVEL REC

REW

REC

PREV

NEXT

PLAY

REVIEW

1 CLIP PLAY

SOURCE SELECT

NEW

INT

REGEN

PRESET

EXT

MARKER

VAR

UNITY

VIDEO AUDIO

CH 1-4 CH 5-8

3,5

4,5,6,7

Exporting Data by Card to a Hard
Disk

Hard disk
type

Copy result

Maximum
number of
copies

TYPE S

A partition is created by card and all the

data included in the card are copied to that

partition.

The product number and serial number of

the P2 card used for copying can be

checked on the explorer screen of this unit.

FAT

A folder*

is created by card and all the

data included in the card is copied to that

partition.

The folder name can be checked on the

explorer screen of this unit.

100

OFF

METER

FULL/FINE

MONITOR

SELECT

METER SELECT

INPUT SELECT

REC

THUMBNAIL

PLAYLIST

SET

MENU

ENTRY

SLOT CLIP

PF1

ALL CLIP

PF3

SHIFT

PF4

CLIP LIST

PF2

SLOT SELECT

LAST X

TRIM

DELETE

VIDEO

GO TO

OUT

EDIT MODE

A.DUB
MODE

DIAG

OPERATION

EXIT

CANCEL/PF

MULTI

SEL

CH 1

CH 2

CH 3

CH 4

TEXT

MEMO

TCG

TC PRESET

PROP

RESET

COUNTER

PLAYER

STOP

STILL/

PAUSE

PREVIEW

A.LEVEL REC

REW

REC

PREV

NEXT

PLAY

REVIEW

1 CLIP PLAY

SOURCE SELECT

NEW

INT

REGEN

PRESET

EXT

MARKER

VAR

UNITY

VIDEO AUDIO

CH 1-4 CH 5-8

5,6,7

Содержание AJ-HPM200E







































































































































































































































Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200E, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды