Panasonic AJ-HPM200E Скачать руководство пользователя

Страница: 209 / 230

For Long and Trouble-Free Operation: Error Messages

209

r L

ong

and

le-

ree
O
per

ion

If “E- * * ” Iights in the monitor display, hold down the SHIFT button and press the MENU button to open the DIAG-MENU and

read the warning information.

INVALID TRACK

SELECT

Displayed when no audio track is selected or 3 or more channels are selected in

a voice-over recording on a P2 card.

Only 2 channels can be recorded in a voice-over recording.

Operation

continues

CANTADUB

LACK OF REC

CAP.

Displayed when a voice-over recording is attempted on a P2 card or when

external device or external input is selected for a player of the playlist and the

REC button is pressed to start recording, while there is not enough free space on

the card.

Operation

continues

CANTADUB

MARK ON/OFF

Displayed for two seconds when a shot mark is added or deleted.

Operation

continues

MARK ON /

MARK OFF

MAX. EVENTS

The number of events that can be registered on the playlist has been reached.

Operation

continues

Counter value

NEED TO REPAIR

Displayed when an SD memory card that needs to be repaired is detected.

(When an AJ-YCX250G AVCHD codec board (optional) is installed.)

Operation

continues

ND REP

NO INPUT

Displayed for the first two seconds when the REC button is pressed to enter the

EE mode and the INPUT SELECT button is set to a connector with no output

except for analog audio signals.

Operation

continues

NO INPUT

PL FILE NOT

FOUND

Displayed when a voice-over recording is attempted on a P2 card and there is no

playlist file.

Operation

continues

CANTADUB

REC LIMIT SD

Displayed when recording cannot continue because there is no space or

because a 12-hour recording has been completed.

(When an AJ-YCX250G AVCHD codec board (optional) is installed.)

Operation

continues

LIMIT SD

REPAIRING SD

Displayed when an SD memory card clip is being repaired.

(When an AJ-YCX250G AVCHD codec board (optional) is installed.)

Operation

continues

REPAIR

R-OUT NOT

AVAILABLE

Displayed when an attempt was made to use a recorder OUT point during insert

editing in playlist mode.

Operation

continues

Counter value

SLOT SEL

INVALID

Displayed when the SLOT /– button was pressed while it is not possible

to switch P2 card recording slot.

Operation

continues

INVALID

TEXT MEMO

Displayed for two seconds when a text memo is added.

Operation

continues

TEXT MEMO

INVALID

Appears when there are already 100 text memos and no more memos can be

added.

Operation

continues

INVALID

WRITE

PROTECTED

Appears when a voice-over recording is attempted on a write-protected P2 card. Operation

continues

CANTADUB

WARNING information

Display

Description

Deck operation

Character code

UNKNOWN SIG

Displayed when a signal input from the 1394 interface is not a DVCPRO or DV format

signal.

Recording is

disabled

FAN STOP

Displayed when the fan motor stops.

Operation

continues

NOT 1× 25M SIG

Displayed when a signal input from the 1394 interface is not a DVCPRO (25 Mbps) 1×

normal speed transfer signal.

Recording is

disabled

NOT 1× 50M SIG

Displayed when a signal input from the 1394 interface is not a DVCPRO50 (50 Mbps) 1×

normal speed transfer signal.

Recording is

disabled

NO MATCH SIG

Displayed when signal input via the 1394 interface differs from the system format set on

this unit.

Recording is

disabled

NOT 1× DV SIG

Displayed when a signal input from the 1394 interface is not a DV (25 Mbps) 1× normal

speed transfer signal.

Recording is

disabled

INVALID VIDEO SIG

Displayed when the compressed video data of a signal input from the 1394 interface is

irregular.

Recording is

disabled

Monitor display

Description

Deck operation

Counter display

Содержание AJ-HPM200E







































































































































































































































Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200E, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды