Panasonic AJ-HPM200E Скачать руководство пользователя

Страница: 130 / 230

130

Connections: Using This Unit With a Hard Disk

Partitions or holders are selected and

changes to

You can now use the selected partition or folder as a

target for processing.

The selected areas remain available until the hard disk is

disconnected or the power it turned off. To release a

selected partition, press the ENTRY button again in the

selected partition. Use the CANCEL (SHIFT + EXIT) button

to cancel all selected areas.

• A warning appears when an attempt is made to select a 7th

area.

◆

NOTE:

• A clip recording that spans several partitions one of whose

MODEL has become UNKNOWN

on a TYPE S hard disk will

not run as a normal clip.

When a clip is copied to a TYPE S hard disk, the MODEL of

the partition storing the copy changes to UNKNOWN.

To name a partition (up to 20 characters), choose [CHANGE

PARTITION NAME] in the [OPERATION] menu in hard disk

thumbnail view.

◆

NOTE:

• A TYPE S hard disk makes it possible to set partition names. The

selected partition name appears in "PARTITION NAME" in the

explorer screen.

Use the cursor buttons to select a partition or folder

to name. Or press the SET button repeatedly to open

the thumbnail list screen.

Press the MENU button and use the cursor buttons

to choose [OPERATION] - [CHANGE PARTITION

NAME] and press the SET button.

Enter the name of the partition using the on-screen

keyboard that appears.

Press the ENTRY button to confirm the name.

Use the steps below to delete the last partition.

◆

NOTE:

• The last partition can only be deleted on a TYPE S hard disk. This

function can delete only the last partition and not any intermediate

partitions.

• Make sure the partition to be deleted does not contain any data you

need as it will not be possible to recover it after deletion.

Move the cursor to the last partition in the hard disk

explorer screen and open the menu.

Choose [OPERATION] – [DELETE LAST

PARTITION] and press the SET button.

Select [YES] in the confirmation message that

appears.

When the partition has been deleted, “COMPLETE”

appears and the last partition disappears from the list

of partitions.

Naming a partition

Deleting the last partition

Содержание AJ-HPM200E







































































































































































































































Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200E, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды