Panasonic AJ-HPM200E Скачать руководство пользователя

Страница: 95 / 230

iti

Editing: Creating Playlists

Creating Playlists

To register an event in a playlist, either set IN and OUT points

using the player and the recorder, or select clips from the

player thumbnails.

Defining any three of four points (the IN and OUT points of

both the player and the recorder) automatically defines the

remaining point.

It is also possible to set only the IN points for the player and

the recorder.

◆

NOTE:

• When only the IN points for the player and the recorder are set and

the player is a P2 card or hard disk, the audio and video of the event

from the IN point of the player until the end of the clip where the IN

point is set is inserted at or starts overwriting data from the recorder

IN point.

• When an external device or external input (live recording) is used as

the player, audio and video up to 24 hours (excluding the preview

time) is inserted or starts overwriting data at the IN point of the

recorder.

• When an external input (live recording) is used as the player, IN and

OUT points of the player cannot be registered.

Select a P2 card, hard disk, external device (RS-422A), or

external input (live recording) as a player.

A P2 card is normally used as a player. Follow the steps below

to select other devices or external input (live recording) as a

player or to again select a P2 card as a player.

Press the PLAY LIST button to open the playlist

screen.

Press the SOURCE SELECT (SHIFT + PLAYER)

button.

Use the cursor buttons to select an interface for the

player and press the SET button.

This determines the external device (interface) that can be

remotely operated.

➝

For details on connecting and setting up external

devices, refer to “Connections” (page 122) and

“External Remote Control” (page 135).

◆

NOTE:

• Devices connected using IEEE1394 cannot be used as external

devices.

Registering Events in a Playlist

Setting IN and OUT points to assign an
event

Selecting player

OFF

METER

FULL/FINE

MONITOR

SELECT

METER SELECT

INPUT SELECT

REC

THUMBNAIL

SET

MENU

ENTRY

SLOT CLIP

PF1

ALL CLIP

PF3

SHIFT

PF4

CLIP LIST

PF2

SLOT SELECT

LAST X

TRIM

DELETE

VIDEO

GO TO

OUT

EDIT MODE

A.DUB
MODE

DIAG

OPERATION

EXIT

CANCEL/PF

MULTI

SEL

CH 1

CH 2

CH 3

CH 4

TEXT

MEMO

TCG

TC PRESET

PROP

RESET

COUNTER

PLAYER

STOP

STILL/

PAUSE

PREVIEW

A.LEVEL REC

REW

REC

PREV

NEXT

PLAY

REVIEW

1 CLIP PLAY

SOURCE SELECT

NEW

INT

REGEN

PRESET

EXT

MARKER

VAR

UNITY

VIDEO AUDIO

CH 1-4 CH 5-8

PLAYLIST

Содержание AJ-HPM200E







































































































































































































































Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200E, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды