Panasonic AJ-HPM200E Скачать руководство пользователя | Manualshive

Страница: 109 / 230

background image

Ed

iti

n

g

Editing: Recording Voice-Overs

109

Recording Voice-Overs

This function allows you to make voice-overs and use them in editing.

Recording can be performed on one or two channels. It is also possible to mix input sound with playback sound.

Voice-overs are displayed on the timeline as an audio event.

◆

NOTE:

• The audio data for a voice-over is written to the P2 card storing the playlist file. Thus the playlist must be saved before audio recording or a

warning will be displayed and recording is disabled.

• A recording of up to 720 minutes can be made at a time.

• Check the remaining space on the P2 card before saving the playlist. Otherwise there may not be enough space for the voice-over recording.

When the P2 becomes full, an error occurs and recording is disabled.

• Setting 24, 60-24 in setup menu No. 25 (SYSTEM FREQ) will disable voice-over recording.

• If the card with the voice-over is not inserted (and the event is indicated in red (X)), the audio event cannot be deleted and a playlist file cannot

be saved.

• The audio channels for audio events created for voice-over recording cannot be switched.

➝

For details on switching audio channels, refer to “Switching audio channels” (page 104).

• Voice-overs cannot be recorded on players other than a P2 card. Select a P2 card as the player before start of recording.

Make the required settings prior to a voice-over recording.

➝

For details on settings, refer to “Setup” (page 166).

You can select whether to mix the playback sound with input

sound during a voice-over in setup menu No. 793 (A DUB PB

MIX).

◆

NOTE:

• In playlist playback, playback level is fixed at UNITY or set to

registered level and cannot be changed. However, the playback

level of EE audio for tracks recorded during voice-over recording

can be adjusted.

• The playback level of preroll for voice-over recording from still status

cannot be changed.

In setup menu No. 797 (A DUB MONI), select whether the

recorded audio should be output during the voice-over.

Setup example:

Connect a microphone to analog CH2 and mix the

microphone input with CH2 playback audio in the recording.

Use headphones to listen to the playback audio during

recording.

◆

NOTE:

• Input a reference signal when mixing using SDI input audio.

• IEEE1394 input audio cannot be used for voice-overs.

Preparing for Voice-Overs

Mixing playback sound

Setting output audio during recording

Selecting recording tracks

Select only the A2 track in

the GUI.

Mixing with playback sound

Set setup menu No. 793

(A DUB PB MIX) to ON.

Setting playback to start

simultaneous with recording

Set setup menu No. 797

(A DUB PB MONI) to ON.

«
...
107
108
109
110
111
...
»

Содержание AJ-HPM200E







































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AJ-HPM200E

Giraffe OmniBed

Бренд: Ohmeda Страницы: 54

Бренд: Napoleon Страницы: 2

Бренд: Raytheon Страницы: 62

Бренд: Landoll Страницы: 52

Бренд: Gason Страницы: 110

Бренд: h/p/cosmos Страницы: 81

Бренд: jablotron Страницы: 2

Бренд: jablotron Страницы: 2

ENET-232 Series

Бренд: National Instruments Страницы: 105

Бренд: YMC Страницы: 49

Бренд: Octane Fitness Страницы: 8

Бренд: Octane Fitness Страницы: 10

Бренд: OCENCO Страницы: 48

Бренд: Ocean Optics Страницы: 6

Бренд: Gaspardo Страницы: 88

Littmann Classic II Pediatric

Бренд: 3M Страницы: 53

Бренд: Posture Pump Страницы: 2

Бренд: WAGNER Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды