Panasonic AJ-HPM200E Скачать руководство пользователя

Страница: 17 / 230

Introduction: Features

In
tr

odu

tio

■

Connecting a P2 Card Camera

A P2 card recorded in a P2 camera recorder plugs directly

into a PC card slot in this unit for immediate access. The P2

card is a semiconductor memory card that Panasonic

developed for professional AV use.

■

AVC-Intra standard feature

The AVC-Intra codec is provided as a standard feature.

An Intra-Frame compression format based on the H.264 video

compression standard makes possible a high compression

rate and high-quality image.

The AVC-Intra codec for this product is compatible with the

following two formats.

AVC-Intra 100: High-quality video supporting full-bit HD

AVC-Intra 50: Low-rate and low-cost operation

■

24-bit audio supported

The AVC-Intra codec allows the setting of 24-bit or 16-bit

audio recording, using setup menu No. 034 (A.SMPL RES).

When 24-bit audio is selected, audio is recorded in 4

channels.

◆

NOTE:

• Audio recording is fixed at 16-bit recording when a codec other than

AVC-Intra is selected, regardless of the setting of setup menu

No. 034 (A.SMPL RES).

• To play a clip recorded in 24-bit audio, use P2 equipment or a

viewer that supports 24-bit audio.

• When a clip recorded in 24-bit audio is down-converted and played,

16-bit audio is output from the SDI output, while 24-bit audio output

is retained for the AES/EBI output.

• If a clip recorded in 24-bit audio is intended to be played back on

equipment that does not support 24-bit audio, the number of the clip

is shown in red, and playback is impossible.

• If a clip recorded in 24-bit audio is intended to be played back with

a P2 viewer that does not support 24-bit audio, the sound is not

played back properly. Use the latest version of the P2 viewer.

➝

Refer to “Handling P2 Card Recording” (page 220).

■

Built-in up/down/cross converter for output and
up converter for input

The AJ-HPM200 provides a built-in up/down/cross converter

for output as standard. It also up-converts composite and

SD-SDI input signals to record in the same HD format as the

system.

◆

NOTE:

• The cross converter function is not available during up-conversion

recording.

• SD closed caption signals during up-conversion recording are

recorded in the 608 HD (VANC) signal format (59.94 Hz only).

• Closed caption signals are not output during playback or down- and

cross-conversion.

• Nor are closed caption signals output during playback of up-

converted SD signals.

■

Frame rate conversion

Recording input from variable frame-rate cameras at 24PN

(Native), the unit is also capable of playing back cards

recorded at 24 fps and converting the output to 1080/24 PsF.

It can also record input from a variable frame-rate camera at

25PN (Native).

◆

NOTE:

• Do not use cards that have been edited or contain clips shot in

different formats as the loss of management data may prevent

normal playback.

■

Native recording

The unit provides support for native recording, a mode that

records only active frames. This provides longer recording

time when a VariCam, AJ-HPX2000/2100 or AJ-HPX3000 is

connected to the HD-SDI IN connector. Variable frame rate

(VFR) recording becomes possible by connecting a VariCam.

●

Native recording defined

Native recording extracts only the active frames during 1080i

AVC-Intra recording as well as 720P DVCPRO HD and

AVC-Intra recording. At 720P, this lengthens the recording

time 2 to 2.5 times over pull-down recording.

During native recording at a 59.94 Hz or 50 Hz setting in setup

menu No. 25 (SYSTEM FREQ), the unit produces pull-down

output.

■

Thumbnails for managing clips visually

The 230 mm (9 inch) color LCD monitor displays video clips

(thumbnails) stored on a P2 card. The viewer can select the

thumbnails he wants to see and change the order in which

they appear.

Clips can be selected from the thumbnail list for immediate

playback. The list also provides quick access to other clip

management operations such as copying and deleting,

adding shot marks and text memos as well as confirming and

editing clip data.

Ao Ae Bo Be Bo Ce Co De Do De

C D

Example of 1080-24PN (Native)

Example of 720-24PN (Native)

Camera video

2:3 pull-down

Native recording

Camera video

2:3 pull-down

Active frames

Native recording

Содержание AJ-HPM200E







































































































































































































































Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200E, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды