Panasonic AJ-HPM200E Скачать руководство пользователя страница 128

Страница: 128 / 230

128

Connections: Using This Unit With a Hard Disk

Use the following steps to copy selected clips rather than

entire cards to a hard disk.

Connect a hard disk.

Press the THUMBNAIL button to open the thumbnail

screen, select the clip to copy using the cursor

buttons, and press the SET button to confirm.

You can also select multiple clips.

Press the MENU button.

Use the cursor buttons to select [OPERATION] -

[COPY] -[HDD (USB or eSATA)] and press the SET

button.

Select the location of the clip in the hard disk folder

or partition list that appears and press the SET

button.

◆

NOTE:

• A hard disk in the FAT format will display the following folders.

- Root folder

- Up to three levels of folders containing CONTENTS folder

• Copying is not possible on a TYPE S hard disk without a single

partition. To enable copying, format using a FAT format or

create a partition by exporting data.

Select [YES] and press the SET button.

The clip will now be copied. A progress bar appears

during copying.

◆

NOTE:

• To interrupt copying, use the cursor buttons to select CANCEL

and press the SET button. Then select [YES] in the confirmation

dialog that appears and press the SET button again. The

incomplete copy at the destination is deleted.

• When a clip is copied to a TYPE S hard disk, it will not be

possible to import data by card from the partition. The card

model number is then displayed as “UNKNOWN.”

When the copy operation ends, “COPY COMPLETED!”

appears.

Use the steps below to display hard disk information and

select hard disk partitions and folders. A selected partition

can also easily be used as a player in editing playlists.

Connect a hard disk.

Press the MENU button in the thumbnail screen.

Copying Clips to a Hard Disk

OFF

METER

FULL/FINE

MONITOR

SELECT

METER SELECT

INPUT SELECT

REC

THUMBNAIL

SET

MENU

ENTRY

SLOT CLIP

PF1

ALL CLIP

PF3

SHIFT

PF4

CLIP LIST

PF2

SLOT SELECT

LAST X

TRIM

DELETE

VIDEO

PLAYLIST

GO TO

OUT

EDIT MODE

A.DUB
MODE

DIAG

OPERATION

EXIT

CANCEL/PF

MULTI

SEL

CH 1

CH 2

CH 3

CH 4

TEXT

MEMO

TCG

TC PRESET

PROP

RESET

COUNTER

PLAYER

STOP

STILL/

PAUSE

PREVIEW

A.LEVEL REC

REW

REC

PREV

NEXT

PLAY

REVIEW

1 CLIP PLAY

SOURCE SELECT

NEW

INT

REGEN

PRESET

EXT

MARKER

VAR

UNITY

VIDEO AUDIO

CH 1-4 CH 5-8

2,4,5,6

Displaying Hard Disk Information
(Explorer Screen)

Содержание AJ-HPM200E







































































































































































































































Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200E, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200E

Отзывы:

Похожие инструкции для AJ-HPM200E

Бренды по названию

Популярные бренды