![background image](http://html1.mh-extra.com/html/omron/sysmac-c200h/sysmac-c200h_operation-manual_742423227.webp)
214
SYSMAC LINK Systems
Refer to the SYSMAC LINK System Manual for details.
Word
Bits 00 to 07
Bits 08 to 15
C
Number of words (0 to 256 in 4-digit hexadecimal, i.e., 0000
hex
to 0100
hex
)
C+1
Response time limit (0.1 and 25.4
seconds in 2-digit hexadecimal
without decimal point, i.e., 00
hex
to
FF
hex
)
Note:
The response time will be
2 seconds if the limit is set to 0
hex
.
There will be no time limit if the
time limit is set to FF
hex
.
Bits 08 to 11:
No. of retries (0 to 15 in
hexadecimal,
i.e., 0
hex
to F
hex
)
Bit 12:
Set to 0.
Bit 13:
Set to 0.
Bit 14 ON: Operating level 0
OFF: Operating level 1
Bit 15:
Set to 1.
C+2
Source node (0 to 62 in 2-digit
hexadecimal, i.e., 00
hex
to 3E
hex
)
Set to 0.
Examples
This example is for a SYSMAC NET Link System. When 00000 is ON, the
following program transfers the content of IR 001 through IR 005 to LR 20
through LR 24 on node 10.
0
0
0
5
0
0
0
0
0
0
0
A
IR 001
IR 002
IR 003
IR 004
IR 005
LR 20
LR 21
LR 22
LR 23
LR 24
DM 0010
DM 0011
DM 0012
15
0
RECV(98)
001
LR 20
DM 0010
00000
Node 10
Address
Instruction
Operands
00000
LD
00000
00001
RECV(98)
001
LR
20
DM
0010
Flags
ER:
The specified node number is greater than 126 in a SYSMAC NET
Link System or greater than 62 in a SYSMAC LINK System.
The received data overflows the data area boundaries.
Indirectly addressed DM word is non-existent. (Content of
*
DM word
is not BCD, or the DM area boundary has been exceeded.)
There is no SYSMAC NET Link/SYSMAC LINK Unit.
5-23-3
About SYSMAC NET Link/SYSMAC LINK Operations
SEND(90) and RECV(98) are based on command/response processing. That
is, the transmission is not complete until the sending node receives and ac-
knowledges a response from the destination node. Note that the
SEND(90)/RECV(98) Enable Flag is not turned ON until the first END(01)
after the transmission is completed. Refer to the SYSMAC NET Link System
Manual or SYSMAC LINK System Manual for details about command/re-
sponse operations.
SYSMAC NET Link/SYSMAC LINK Instructions
Section 5-23
Содержание SYSMAC C200H
