7-25
D
RUN Command (Register 0001 Hex)
Bit No.
Function
0
RUN command (1: RUN)
1
Forward/Reverse (1: Reverse)
2
External fault (External fault EF0)
3
Fault reset (1: Fault reset)
4
Multi-function input 1 (1: ON)
5
Multi-function input 2 (1: ON)
6
Multi-function input 3 (1: ON)
7
Multi-function input 4 (1: ON)
8
Multi-function input 5 (1: ON)
9
Multi-function input 6 (1: ON)
10
Multi-function input 7 (1: ON)
11 to 15
Not used
Note
There is an OR relationship between input from the control terminals and input
through communications. Therefore, if multi-function inputs of this register are
set to forward/stop and reverse/stop, it is possible to execute the RUN command
through the multi-function inputs. These settings are not, however, recom-
mended because these settings establish two command lines.
D
Inverter Output (Register 0009 Hex)
Bit No.
Function
0
Multi-function contact output (1: ON)
1
Multi-function output 1 (1: ON)
2
Multi-function output 2 (1: ON)
3 to 15
Not used
Note
The settings will be enabled if multi-function outputs 1 through 3 in n057 through
n059 are set to 18 for communications output. Then the corresponding output ter-
minal will be turned ON and OFF through communications.
H
Broadcast Message with Slave Address: 00 (00 Hex)
Write
Register No.
(Hex)
Function
Description
0000
Not used
---
0001
RUN command
Refer to the table below.
0002
Frequency reference
Set the frequency reference based on the
maximum frequency as 30,000.
0003 to 000F
Not used
---
Note 1.
Data can be written to registers 0001 and 0002 only.
Communications
Chapter 7
Содержание SYSDRIVE 3G3MV A2002
