![background image](http://html1.mh-extra.com/html/omron/c200h-mc221/c200h-mc221_operation-manual_742324241.webp)
221
Code
Error Processing
Error
0081
ABS soft reset range over
(ABS SFT RSET OVR)
The current position data exceeded the range from –32767 to +32767 pulses.
Shift the current position to a position within
±
32767 pulses and try again.
0082
Origin proximity & overtravel
simultaneously ON
(OR PRX AND OT ON)
During an origin search, the origin proximity switch and the limit switch in the
direction of the search are both ON at the same time.
Change the mounting positions of the origin proximity switch and limit switch.
Refer to
Appendix B Additional Origin Search Patterns
for details on how errors
occur during origin searches.
0083
Overtravel always ON
(OVER TRAVEL ON)
The limit switch in the direction of the search was already ON when a one
direction-mode origin search was executed.
Check the limit switch in the initial origin search direction. Also check the
location of the axis when the origin search was started. Refer to
Appendix B
Additional Origin Search Patterns
for details on how errors occur during origin
searches.
0084
Origin proximity reverse error
(OR PRX REVROT ER)
The reverse-mode origin search can’t be performed because the limit switch in
the direction of the search came ON while the search was reversing because
of the origin proximity input. This is the same as when the origin proximity input
is also used as a limit switch.
Check the limit switch in the initial origin search direction as well as the
mounting positions of the origin proximity switch and limit switch. Refer to
Reverse-mode Origin Searches 12
in
Appendix B
for details on this error.
0085
Overtravel reverse error
(OT REV ROTAT ERR)
The reverse-mode origin search can’t be performed because the other limit
switch or the origin proximity switch came ON while the search was reversing
because of a limit switch input.
Check the limit switch in the initial origin search direction as well as the
mounting positions of the origin proximity switch and limit switch. Refer to
Reverse-mode Origin Searches 12
in
Appendix B
for details on this error.
0086
Wiring error
(WIRING ERROR)
A wiring error was detected during the wiring check automatically performed
with the servo lock.
Check whether the number of pulses and check time in the wiring check are
correct. If they are correct, check whether the encoder’s A-phase/B-phase
wiring is correct.
0087
MPG ratio overflow
(MPG FACTOR OVER)
The MPG’s ratio (factor) is too great, so the command value can’t be
generated. Reduce the MPG ratio or the frequency of the pulses from the
MPG. (Turn the MPG a little slower.)
0088
Abnormal feedback pulses
(FEEDBK PULSE ERR)
The feedback pulses exceeded 275,000 pps or a task error occurred while the
absolute encoder’s data was being read and the read was cancelled.
The excessive feedback pulse frequency could be caused by a broken encoder
cable, encoder error, or noise.
Take appropriate countermeasures and try again.
Remove the causes that have caused the task error.
Axis Errors: Error Codes 0060 to 0088
Section 10-4
Содержание C200H-MC221 -
