manualshive.com logo in svg

Nidek Medical ME-1000, Руководство по обслуживанию

Поделиться
Скачать
Nidek Medical ME-1000 Скачать руководство пользователя страница 9

2 - 1

LLE11ARDA001A/E

§2 SAFETY PRECAUTIONS

2.1 General Precautions

  • Only the service persons who are accustomed to using tools, and have a deep knowledge of

this instrument are allowed to repair the instrument.

  • Proceed right work in accordance with the procedure.

If not, accidents or failure of the instrument may result.

  • When the instrument is moved, it should be carried by two or more persons.  Otherwise, you

may have a backache or fall down.

  • When performing maintenance works, turn off the power switch, and disconnect the power

cord from the wall outlet unless necessary.

  • Never wipe the covers, etc. using an organic solvent such as a paint thinner.

The surface may be ruined, and as a result, the appearance of the instrument will be impaired.

<Maintenance precautions>

  • In case of instrument malfunction, turn the power switch off after checking the symptom.

  • Never drop parts or screws inside the instrument, nor bump it against the surrounding objects.

  • Have storage cases ready to ensure the loss of the removed screws or parts.

  • In screwing or unscrewing, use a proper tool for the screw.

  • After loosening the screws fixed by a threadlocking adhesive, and tightening them again, be

sure to apply the threadlocking adhesive to them.

  • After replacing parts, make sure that they are fixed securely before turning on the power.

  • If you observe strange odors or smoke being emitted from the instrument, immediately turn

off the instrument and locate the causes after disconnecting the power cord from the wall-
outlet.
If the instrument is continuously powered under such abnormal conditions, a fire, electric
shock or total loss of the instrument may result.

  • Referring to “8.1 Wiring Diagram” and “8.2 Connector Cables”, check cables for the following:

1. Connectors are connected securely.
2. No contact failure occurs after re-connection of connectors.
3. No failure in soldering
Do not pull the cables strongly.  It may cause a breaking of wire.

Содержание ME-1000







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды