Nidek Medical ME-1000 Скачать руководство пользователя

Страница: 127 / 134

8 - 7

LLE11ARDA001A/E

8.5 Error message

No.

Error indication

Contents

Causes and measures

101

101-Roughing was not
completed

Roughing is not completed.

Insufficient dressing of the Glass
wheel

102

102-Finishing was not
completed

Finishing is not completed.

Insufficient dressing of the wheel
(This error message is displayed
when the rotating numbers of the

axis achieves unlikely one.)

201

201-Feeler off error

Feeler is off when starting the
lens measurement.

The lens diameter is insufficient.

202

202-There is no lens

Feeler is off.

Lens is not attached.

203

203-Feeler lift error

Feeler lifts up.

Grind the cataract lens, bifocal
lens and such in EX mode.

204

204-Front & rear data crossed

Measured data is improper.
(Front and rear data was
crossed.)

Failure of the encoder (The thin
lens is deformed.)

205

205-Start & end measure data
error

Measured data at the start point
does not match to the one at the
end point.

Failure of the encoder (Check the
deformation of the thin lens and
attachment of the feelers)

401

401-XYR Initialize error

The X, Y and R axes are not
initialized.

Check the driving transferring unit
of each origin sensor and gears.

402

402-X Initialize error

The X axis is not initialized.

Same as above

403

403-Y Initialize error

The Y axis is not initialized.

Same as above

404

404-R Initialize error

The R axis is not initialized.

Same as above

405

405-XY Initialize error

The X and Y axes are not
initialized.

Same as above

406

406-XR Initialize error

The X and R axes are not
initilized.

Same as above

407

407-YR Initialize error

The Y and R axes are not
initialized.

Same as above

408

408-Front feeler Initialize error

Front of the F axis is not
initialized.

Same as above

409

409-Rear feeler Initialize error

Rear of the F axis is not
initialized.

Same as above

410

410-Drill ZR Initialize error

Drill Z and R axes are not
initialized.

Same as above

411

411-Drill Z Initialize error

Drill Z axis is not initialized.

Same as above

412

412-Drill R Initialize error

Drill R axis is not initialized.

Same as above

413

413-SFB Initialize error

The SFB arm is not initialized.

Same as above

501

501-Chuck origin error

Chuck origin sensor does not
respond.

Same as above

601

601-Main wheel was not rotate The main wheel does not rotate.

Check the LED indication of the
inverter.

603

603-SFB wheel was not rotate The SFB wheel does not rotate.

Same as above

701

701-Cover open error

Cover error (OPEN)

The cover does not open by
pressing the Cover button after the
processing.

702

702-Cover close error

Cover error (CLOSE)

The cover does not close by
pressing the Start and Cover
buttons.

Содержание ME-1000







































































































































Результаты поиска

Содержание ME-1000

Отзывы:

Похожие инструкции для ME-1000

Бренды по названию

Популярные бренды

Nidek Medical ME-1000, Руководство по обслуживанию

Результаты поиска

Содержание ME-1000

Отзывы:

Похожие инструкции для ME-1000

Бренды по названию

Популярные бренды