Mitsubishi Electric FR-A800, Инструкция по эксплуатации

Страница: 68 / 1042

Control circuit Installation and wiring
2 - 38
Output signal
Terminal FM is provided in the FM-type inverter.
Terminal CA is provided in the CA-type inverter.
Ty
p
e
Terminal
Symbol
Terminal name Terminal function description Rated specification
Refer
to
page
Re
la
y
A1,
B1,
C1
Relay output 1 (fault
output)
1 changeover contact output that indicates that
an inverter's protective function has been
activated and the outputs are stopped.
Fault: discontinuity across B and C (continuity
across A and C), Normal: continuity across Band C
(discontinuity across A and C)
Contact capacity
230 V AC 0.3 A
(power factor = 0.4)
30 V DC 0.3 A
5-361
A2,
B2,
C2
Relay output 2 1 changeover contact output 5-361
O
pen c
o
ll
ec
tor
RUN Inverter running
Switched to LOW when the inverter output
frequency is equal to or higher than the starting
frequency (initial value 0.5 Hz). Switched to HIGH
during stop or DC injection brake operation.
Permissible load
24 V DC (maximum
27 V DC) 0.1 A
(The voltage drop is
2.8 V at maximum
while the signal is
ON.)
LOW is when the
open collector output
transistor is ON
(conducted).
HIGH is when the
transistor is OFF (not
conducted).
5-361
SU Up to frequency
Switched to LOW when the
output frequency is within
the set frequency range
±
10% (initial value). Switched
to HIGH during acceleration/
deceleration and at a stop.
Fault code (4 bits)
output. (Refer to
page 5-385.)
5-373
OL Overload warning
Switched to LOW when stall
prevention is activated by
the stall prevention function.
Switched to HIGH when stall
prevention is cancelled.
5-322
IPF
Instantaneous power
failure
Switched to LOW when an
instantaneous power failure
occurs or when the
undervoltage protection is
activated.
5-562,
5-580
FU Frequency detection
Switched to LOW when the
inverter output frequency is
equal to or higher than the
preset detection frequency,
and to HIGH when it is less
than the preset detection
frequency.
5-373
SE
Open collector
output common Common terminal for terminals RUN, SU, OL, IPF,
FU
⎯ ⎯
Pu
ls
e
FM
For meter
Outputs a selected
monitored item (such as
output frequency) among
several monitored items. The
signal is not output during
an inverter reset.
The output signal is
proportional to the
magnitude of the
corresponding monitoring
item.
Use Pr. 55, Pr. 56, and Pr. 866
to set full scales for the
monitored output frequency,
output current, and torque.
(Refer to page 5-341.)
Output item:
Output frequency
(initial setting)
Permissible load
current 2 mA
For full scale
1440 pulses/s
5-341
NPN open
collector output
This terminal can
be used for open
collector outputs
by setting Pr. 291.
Maximum output
pulse 50k pulses/s
Permissible load
current 80 mA
5-282
Anal
og
AM
Analog voltage
output
Output item:
Output frequency
(initial setting)
Output signal 0 to
±
10 V DC,
Permissible load
current 1 mA
(load impedance
10 k
Ω
or more)
Resolution 8 bits
5-341
CA
Analog current
output
Load impedance
200
Ω
to 450
Ω
Output signal
0 to 20 mADC
5-341
Tab. 2-14: Output signals