Appendix 2 Explanation of Alarms
MITSUBISHI CNC
516
L11 DN INIT. ERR. 2 0A (Error-detected module I/O No.)
Details
A deviceNet initialization error has occurred. The error-detected node No. is FEH.
- The watchdog timeout action value in a parameter is invalid.
"Error-detected module I/O No." shows the error-detected module I/O No. with the last digit removed.
Remedy
- Set it to one of the following: 0000H, 0001H, 0002H,
or 0003H.
L11 DN INIT. ERR. 2 0B (Error-detected module I/O No.)
Details
A deviceNet initialization error has occurred. The error-detected node No. is FEH.
- The expected packet rate value in the buffer memory is smaller than the production inhibit time
value.
"Error-detected module I/O No." shows the error-detected module I/O No. with the last digit removed.
Remedy
- Change the value so that the expected packet rate is greater than or equal to the production inhibit
time value.
L11 DN INIT. ERR. 2 0C (Error-detected module I/O No.)
Details
A deviceNet initialization error has occurred. The error-detected node No. is FEH.
- Flash ROM checksum error (parameter area for the master function)
"Error-detected module I/O No." shows the error-detected module I/O No. with the last digit removed.
Remedy
- Save the parameters again.
- Do not turn OFF the power or reset while saving the parameters.
L11 DN INIT. ERR. 2 0D (Error-detected module I/O No.)
Details
A deviceNet initialization error has occurred. The error-detected node No. is FEH.
- Flash ROM checksum error (parameter area for the slave function)
"Error-detected module I/O No." shows the error-detected module I/O No. with the last digit removed.
Remedy
- Save the parameters again.
- Do not turn OFF the power or reset while saving the parameters.
L11 DN INIT. ERR. 2 0E (Error-detected module I/O No.)
Details
A deviceNet initialization error has occurred. The error-detected node No. is FEH.
- Flash ROM checksum error (auto communication start setting area)
"Error-detected module I/O No." shows the error-detected module I/O No. with the last digit removed.
Remedy
- Save the parameters again.
- Do not turn OFF the power or reset while saving the parameters.
L11 DN INIT. ERR. 2 0F (Error-detected module I/O No.)
Details
A deviceNet initialization error has occurred. The error-detected node No. is FEH.
- Flash ROM all clear error
"Error-detected module I/O No." shows the error-detected module I/O No. with the last digit removed.
Remedy
- Save the parameters again.
- Do not turn OFF the power or reset while clearing all parameters.
Содержание C70
