2 GOT Initial Setup
MITSUBISHI CNC
22
2.1.5 Transferring the Data to GOT (Using an USB cable)
Install OS on GOT and then transfer the project data, where required settings have been made, to GOT.
This section explains the procedure when using an USB cable.
When using a CF card, refer to "Transferring the Data to GOT (Using a CF card)".
2.1.5.1 Installing OS on GOT
OS, including standard monitor OS and communication driver, is necessary to make GOT operate. Make sure to install
them before downloading the created project data.
See below for the details of each data. For details, refer to the "GT Designer3 Version1 Screen Design Manual
(Fundamentals)" (SH(NA)-080866), Section 8.
(1)
Turn ON the GOT, start GT Designer3 on the personal computer, and select [Communication]-[Communication
Configuration...] from the menu bar.
(Note)
At starting GT Designer3, if the "New Project Wizard" dialog box appears, close the dialog box.
Data type
Outline
Storage destination (Drive in GOT)
BootOS
The software required to control the GOT hardware and
make a communication between the PC and GOT. (Note)
Factory-installed. Reinstallation is not generally required.
C: Built-in Flash Memory
OS(Standard
monitor OS)
The software for operating the monitor function, touch key
control, system screen and guidance display function and
other features.
A: Standard CF Card or C: Built-in
Flash Memory
Project data
User screen data, common settings, comment, High Quality
font, True Type font, etc.
A: Standard CF Card or C: Built-in
Flash Memory
GT09-C20USB-5P
GT09-C30USB-5P
USB
GOT1000 Series
(SVGA / XGA)
GT Designer3
Содержание C70
