Appendix 1 Explanation of Parameters
MITSUBISHI CNC
186
【
#1092
】
Tchg _A Replace tools for additional axis
Select the movement of the additional axis at the tool change position return command.
0: The additional axis will not move
1: After the standard axis returns, the additional axis will also return to the tool change position
【
#1093
】
Wmvfin Synchronization between part systems method
Select the timing of synchronization between part systems when using the multi-part system.
When the travel command is found in the synchronization command (!) block:
0: Synchronize before executing travel command
1: Synchronize after executing travel command
【
#1094
】
Tl_SBK Select life count for single block (for L system only)
Select whether to count the data units to be used for single block operation when using the tool life
management II function (L system).
0: Not count
1: Count
【
#1095
】
T0tfof TF output (for L system only)
Select how to handle TF for T00 command.
0: TF will be output
1: TF wont be output
【
#1096(PR)
】
T_Ltyp Tool life management type (for L system only)
Select the tool life management type.
1: Life management l
In this type, how long and how many times the program commanded tool is used are
accumulated to monitor the usage state.
2: Life management ll
This method is the same as tool life management I, but with the spare tool selection function.
A spare tool is selected from a group of tool commands commanded in the program.
Tool compensation (tool length compensation and tool radius compensation) is carried out for
the selected tool.
【
#1097
】
Tldigt Tool wear compensation number 1-digit command
Select the number of digits of the tool wear compensation No. in the T command.
0: The 2 high-order digits are the tool No., and the 2 low-order digits are the wear compensation
No.
1: The 3 high-order digits are the tool No., and the 1 low-order digit is the wear compensation No.
This parameter will be fixed to “0” when tool life management II is selected.
【
#1098
】
Tlno. Tool length offset number
Select the number of digits of the tool length compensation No. in the T command.
0: The 2 or 3 high-order digits are the tool No.
The 2 or 1 low-order digits are the tool length compensation and wear compensation Nos.
1: The 2 or 3 high-order digits are the tool No. and tool length compensation Nos.
The 2 or 1 low-order digits are the wear compensation No.
【
#1099
】
Treset Cancel tool compensation amount
Select how to handle the tool compensation vector when resetting the system.
0: Clear the tool length and wear compensation vectors when resetting
1: Hold the tool length and wear compensation vectors when resetting
When the values are cleared, the compensation will not be applied. So the axis will be shifted by the
compensation amount in the next compensation operation.
When the values are kept, the compensation will be applied, so the axis will shift the differential
amount of the compensation amount in the next compensation operation.
Содержание C70
