C70 Setup Manual
Appendix 1.6 Spindle Parameters
299
【
#3127
】
SPECSP Spindle specification
bit0: Output conditions of spindle changeover mode and spindle speed reach signals
0: Conventional operation
- Spindle changeover mode signal
When the spindle stop signal is ON and when a gear recommended by NC and the one selected
in ladder program are different, the spindle changeover mode signal is output to the spindle
drive unit.
- Spindle speed reach signal
Spindle speed reach signal is turn ON/OFF according to the FB signal.
1: Operation when the gear responds to the neutral state under full-closed control
- Spindle changeover mode signal
When both the spindle stop signal and the spindle gear shift signal are ON, the spindle
changeover mode signal is output to the spindle drive unit.
- Spindle speed reach signal
During gear changeover (while gear changeover is being commanded), the spindle speed reach
signal is turned ON/OFF according to the virtual spindle-end speed that is calculated by
multiplying the motor-end speed by the gear ratio (motor-end gear teeth/spindle-end gear teeth).
---Setting range---
0x0000 to 0xffff (hexadecimal)
【
#3130
】
syn_spec Spindle synchronization specification
bit1: Acceleration/ deceleration type in phase alignment
0: Phase alignment method Type 2 (Acceleration/ deceleration method)
1: Phase alignment method Type 1 (Step alignment method)
【
#3140(PR)
】
S_DINSp Speed monitor input door No.
Set the door signal input in the drive unit.
Use this parameter only when the axis with a door signal belongs to several door groups.
The correspondence between the door signals and bits are as follows.
bit0 : Door1 signal
bit1 : Door2 signal
:
bitF : Door16 signal
If the axis does not receive any door signal, set to "0".
An error (Y20 0027) will occur in the following cases.
- Several bits are enabled.
- Any bit other than those set in "#3071 S_DSlSp" is enabled.
---Setting range---
0000 to FFFF (HEX)
【
#3141(PR)
】
spsscfeed1 Safety observation speed 1
Set the safety observation speed, which is at the machine end, in the multi-step speed monitor mode
1.
(Note) The lower two digits of the setting value are ignored. An input value "1234567" is recognized
as "1234500", "99" is "0".
---Setting range---
0 to 1800000 (°/min)
【
#3142(PR)
】
spsscfeed2 Safety observation speed 2
Set the safety observation speed, which is at the machine end, in the multi-step speed monitor mode
2.
(Note) The lower two digits of the setting value are ignored. An input value "1234567" is recognized
as "1234500", "99" is "0".
---Setting range---
0 to 1800000 (°/min)
Содержание C70
