Appendix 1 Explanation of Parameters
MITSUBISHI CNC
332
【
#13194
】
SP194 LMN Base speed for load meter standard output (High-speed coil)
Set the base speed of the standard output to be displayed as 100% in load meter.
When "0" is set, the base speed of the short-time rated output will be applied.
It is not available for MDS-DJ-SP Series.
---Setting range---
0 to 32767 (r/min)
【
#13195
】
SP195 LMRL Change magnification for load meter standard output (Low-speed
coil)
Set the standard output to be displayed as 100% in load meter using the short-time rated output
ratio.
To display the continuous rated output as 100%, set as follows.
Continuous rated output/Short-time rated output × 100
When "0" is set, normal display will be applied.
It is not available for MDS-DJ-SP Series.
---Setting range---
0 to 100 (%)
【
#13196
】
SP196 LMNL Base speed for load meter standard output (Low-speed coil)
Set the base speed of the standard output to be displayed as 100% in load meter.
When "0" is set, the base speed of the short-time rated output will be applied.
It is not available for MDS-DJ-SP Series.
---Setting range---
0 to 32767 (r/min)
【
#13197
】
SP197
Not used. Set to "0".
【
#13198
】
SP198
Not used. Set to "0".
【
#13199
】
SP199
Not used. Set to "0".
【
#13200
】
SP200
Not used. Set to "0".
【
#13201
】
SP201
Not used. Set to "0".
【
#13202
】
SP202
Not used. Set to "0".
【
#13203
】
SP203
Not used. Set to "0".
【
#13204
】
SP204
Not used. Set to "0".
【
#13205
】
SP205
Not used. Set to "0".
【
#13206
】
SP206
Not used. Set to "0".
Содержание C70
