C70 Setup Manual
Appendix 2.13 Program Errors (P)
533
P275 MACRO ARG. EX.
Details
The number of argument sets in the macro call argument type II has exceeded the limit.
Remedy
- Correct the program.
P276 CALL CANCEL
Details
A G67 command was issued though it was not during the G66 command modal.
Remedy
- Correct the program.
- Issue G66 command before G67 command, which is a call cancel command.
P277 MACRO ALM MESG
Details
An alarm command has been issued in #3000.
Remedy
- Refer to the operator messages on the diagnosis screen.
- Refer to the instruction manual issued by the machine tool builder.
P280 EXC. [ ‚ ]
Details
Over five times have the parentheses "[" or "]" been used in a single block.
Remedy
- Correct the program so that the number of "[" or "]" is five or less.
P281 [ ‚ ] ILLEGAL
Details
A single block does not have the same number of commanded parentheses "[" as that of "]".
Remedy
- Correct the program so that "[" and "]" parentheses are paired up properly.
P282 CALC. IMPOSS.
Details
The arithmetic formula is incorrect.
Remedy
- Correct the formula in the program.
P283 DIVIDE BY ZERO
Details
The denominator of the division is zero.
Remedy
- Correct the program so that the denominator for division in the formula is not zero.
P290 IF SNT. ERROR
Details
There is an error in the "IF[<conditional>]GOTO(" statement.
Remedy
- Correct the program.
P291 WHILE SNT. ERR
Details
There is an error in the "WHILE[<conditional>]DO(-END(" statement.
Remedy
- Correct the program.
Содержание C70
