Mitsubishi Electric C70, Руководство по установке

Страница: 562 / 628

C70 Setup Manual
Appendix 2.15 Operation Messages on Setting Display Unit
545
E50
E51
E52
E53
E54
E55
E56 FILE ERROR
FILE OPEN ERROR
FILE CLOSE ERR
FILE SEEK ERR
FILE READ ERR
FILE DELETE ERR
FILE INSERT ERR
×
- If one of these errors occurs‚ the editing or input/output operations cannot be
continued. Contact the service center.
As for E50‚ a classification No. will display at the end of the message. Inform the
service center of this No. as well.
E60 IOP ERR **
×
A classification number is displayed after the message for E60.
Refer to the section shown in parentheses‚ and remedy the problem.
E60 lOP ERROR – 4 (E09 time out)
E60 lOP ERROR – 5 (E08 physical err)
E60 lOP ERROR – 7 (E07 reset end)
E60 lOP ERROR – 10 (E04 DEV. NOT READY)
E60 lOP ERROR – 15 (E17 parity H err)
E60 lOP ERROR – 16 (E18 parity V err)
E60 lOP ERROR – 17 (E20 over run error)
E60 lOP ERROR – 18 (E22 code change error)
E60 IOP ERROR – 20 (framing and H/W errors)
- Setting for the bit length is incorrect. (Baud rate, stop bit, and character length)
Check the setting of the I/O device system and its parameters and set it again.
- Check the situations of the connected devices (cable wiring and noise measures).
E62 I/O PARAM ERR Δ
- The
“
EIA code
”
data set for I/O parameter is of an unusable code.
The unusable codes are those used as the EIA standard codes and the even hole
codes.
E64 PROGRAM No. ERR Δ
- The same No. as the program No. designated for program copy was found in the
memory.
- During tape input‚ the first character of the machining program block is the program
No. address "O" or "L".
E65 PROG. No. DUPLl Δ - During tape input‚ the same No. as the specified program was found in the memory.
E66 NO PROG. NUMBER
Δ
- During tape input‚ the program No. was not found on the paper tape‚ and a program
No. was not designated on the screen
’
s data setting area. Set the program No.‚ and
input again.
E69 PROG. CHECK MODE ×
- Search (operation search) was attempted during program check (continuous or
step).
Retry search after the program check is completed‚ or after resetting the program
search
E70 TOOL No. DUPLl Δ
- A tool No. already registered was newly registered on the tool life management
screen.
E71 TOOL ENTRY OVER ×
- Registration of data exceeding the max. No. of registerable tools was attempted on
the tool life management screen.
- When inputting the tool offset data onto tape‚ a compensation number exceeding
the specifications range was specified‚ and that block could not be input. If the input
key is pressed again in the input screen‚ the input will continue from the next block.
E76 TOOL No. ERROR ×
- The offset No. to be used for workpiece coordinate system offset data
measurement was invalid. Restart from tool selection. (Correctly specify the R
register that contains the offset number.)
E77 AXIS NO REF-RET ×
- Zero point return has not been completed for the axis being measured. Return the
axis to the zero point.
E78 AX UNMATCH (TLM ) ×
- During movement of two or more axes‚ the sensor turned on and the tool length was
measured.
Keep off from the sensor and perform the measurement for one axis at a time.
E79 NO REF-RTN (TLM) ×
- The sensor turned on for an axis that has not completed dog- type reference point
return‚ and the tool length was measured. Return the axis to measure to the
reference point.
E81 PROGRAM ERROR ×
- A program error was detected while searching the designated block. Refer to the
directions for the responding program error code being displayed at the same time.
E82 ALREADY RESEARCH ×
- Immediately after completing a restart search in program restart, another search or
restart search was attempted. If program restart operation is continued, the program
will restart from the block searched in the previous search (the axis will be returned
to the restart position automatically or manually). To start over a search, cancel the
previous search by resetting, and then search again.
E84
CAN
’
T IN/OUT
×
- Parameters were input in the setup parameter lock state.
Refer to the instruction manual issued by the machine maker.
- When using the high-speed program server function, the parameter "#1925
EtherNet" parameter was set to "0".
Error No. Error message Details