Mitel Inter-Tel 5000 Скачать руководство пользователя | Manualshive

Страница: 165 / 468

background image

Chapter 5: Installation

Installing a Dual T1/E1/PRI Module (T1M-2)

Inter-Tel

®

5000 Installation Manual – Issue 2.4, May 2008

Page 5-43

Installing a Dual T1/E1/PRI Module (T1M-2)

This procedure assumes the required pre-installation checklist items, regarding T1/E1/PRI, are
in place. If necessary, see “Gathering the Necessary Tools and Supplies” on

page 5-10

.

The Dual T1/E1/PRI module is installed and configured like the single T1/E1/PRI module with
the following exception: Each port on the dual module can be configured differently from the
other. For example, you can configure one port for T1 and the other for T1/PRI or E1/PRI. The
single T1 module provides two ports as well, but one of the ports is for testing purposes. Unlike
the single T1/E1/PRI module, the dual module does not provide the test port.

See Figure 5-20 on

page 5-44

for an illustration of this module.

Procedure

To install a Dual T1/E1/PRI module:

1.

Using a properly terminated anti-static wrist strap, remove the module from the
protective anti-static bag.

2.

Insert the module carefully so that it aligns with the rails inside the chassis, and then
gently slide the module into the chassis until it stops and the module release lever clicks
into place (up position). Do not use force.

3.

Tighten the fastener at the top of the module, securing the module to the chassis. Do not
over tighten this fastener.

IMPORTANT

The Dual T1/E1/PRI module can be removed with power on; however, you
must wait for the REMOVE LED indicator to change to green before
removing the module. Pressing and holding the release lever until the LED
indicator turns green allows the software to “disconnect” from the module.
Not waiting until the LED turns green could result in pending information
getting lost or unexpected system behavior.

Other than the processor module, all other modules can reside in any bay.
However, DB Programming will need to change, if you move a module (that
was previously programmed) into a different bay location.

NOTICE

Before Installing a Dual T1/E1/PRI Module

. If you intend to add or replace a Dual T1/E1/

PRI module, system software must first be upgraded to v2.3 or later. For additional
information, refer to the

Inter-Tel Knowledge Base Center

(www.inter-tel.com/

knowledgebasecenter) article KB3921.

«
...
163
164
165
166
167
...
»

Содержание Inter-Tel 5000





















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Inter-Tel 5000

Бренд: N-Com Страницы: 2

Бренд: Waterway Страницы: 8

Бренд: K&G GROEP Страницы: 27

Бренд: IN-COMMAND Страницы: 47

Medialon MAS Pro Dante D

Бренд: 7th Sense Страницы: 2

Heat Control System

Бренд: ORTAL Страницы: 20

Бренд: Aiwa Страницы: 76

VOCAL SOUND SYSTEM WITH REVERB PA 100

Бренд: Fender Страницы: 8

Dimensions D3200

Бренд: Leviton Страницы: 43

Бренд: Aiwa Страницы: 80

Бренд: Micronix Страницы: 16

Бренд: Discount Car Stereo Страницы: 8

Бренд: Landscape Vibrations Страницы: 8

Бренд: ICON Страницы: 28

CMU 200 / HACx2 . 485x1 . FOTx39 - 12

Бренд: Ediseja 21 Страницы: 20

Бренд: Boss Audio Systems Страницы: 7

Бренд: GE Страницы: 40

SoundStation IP 7000

Бренд: NEC Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды