Inter-Integrated Circuit Peripherals
UG0331 User Guide Revision 15.0
541
15.2.3
Initialization
The I
2
C peripheral can be initialized in the user application software by configuring the I
2
C Control
register and SOFT_RESET_CR system registry. The initialization sequence is as follows:
1.
Release the I
2
C from reset by using SOFT_RESET_CR system registry (
page 540).
2.
Enable I
2
C by writing ‘1’ to the ENS1 bit of
3.
Configure the serial clock rate by using CR0, CR1, and CR2 bits of
4.
Set the slave address to Slave0 Address Register (
).
15.2.3.1 I
2
C Reset
The I
2
C peripherals reset to zero on power-up and are held in reset until enabled. An option is provided
under software control to reset the I
2
C peripherals by writing to bit 11 or bit 12 in the System register,
SOFT_RESET_CR. The soft resets are encoded in the following table.
At power-up, the reset signals are asserted as 1. This keeps the I
2
C peripherals in a reset state. I
2
C
peripheral becomes active when the bit is set to 0, as shown in
15.2.3.2 I
2
C Clock Requirements
The I2C_0 and I2C_1 peripherals are clocked by APB_0_CLK on APB bus 0 and APB_1_CLK on APB
bus 1. These clocks are derived from the main MSS clock M3_CLK. Each APB clock can be
programmed individually as M3_CLK divided by 1, 2, 4 or 8. Refer to the
IGLOO2 Clocking Resources User Guide
for more information.
15.2.3.2.1 Baud Rate Clock
BCLK is a pulse-for-transmission speed control signal and is internally synchronized with the clock input.
BCLK is used to set the serial clock frequency from a clock sourced within the FPGA fabric when the
CR[2:0] bits in the Control register are set to 0b111(0x7). Otherwise, either APB_0_CLK or APB_1_CLK
is used to determine the serial clock frequency. The actual non-stretched serial bus clock frequency can
be calculated based on the settings in the CR[2:0] fields of the Control register and the frequencies of
APB_0_CLK or APB_1_CLK and BCLK. Refer to the
page 551 for more information on
bit settings.
15.2.3.2.2 Clock Stretching
The I
2
C peripherals support the clock stretching feature as defined in Philips I
2
C v2.1 specifications. This
addresses the condition where the I
2
C slave is unable to meet the clock speed provided by the I
2
C
master and needs to slow down. Care should be taken so that the slowest I
2
C device does not dominate
the bus performance. The I
2
C slave is allowed to hold down the clock if it needs to reduce the bus speed.
The I
2
C master reads back the clock signal after releasing it to a High state and waits until the line goes
High.
Clock stretching is a common practice. However, the total bandwidth of the shared bus might significantly
decrease. Estimating the impact of clock stretching is required to share I
2
C bus among multiple devices.
Table 518 •
Soft Reset Bit Definitions For I
2
C Peripherals
Bit
Number Name
R/W Reset Value Description
12
I2C1_SOFTRESETR
R/W 1
Controls reset input to I2C_1
0: Release I2C_1 from reset
1: Keep I2C_1 in reset (reset value)
11
I2C0_SOFTRESET
R/W 1
Controls reset input to I2C_0
0: Release I2C_0 from reset
1: Keep I2C_0 in reset (reset value)
Содержание SmartFusion2 MSS
