background image

Section 3 - On The Water 

Page  36

90-899883234   JANUARY  2008

Safe Boating Suggestions

To enjoy the water safely, you should know and understand all boating regulations and

restrictions that pertain to your activity.
Know and obey all nautical rules and laws of the waterways.
Boat operators should complete a boating safety course.
In the US, courses are offered by:
• The US Coast Guard Auxiliary
• The Power Squadron
• The Red Cross
• Your state or provincial boating law enforcement agency
Direct all inquiries to the Boat U.S. Foundation at 1‑800‑336‑BOAT (2628), or the US Coast

Guard at 1‑202‑372‑1067.
Additional information about boating education and safe boating practices is available on

the following web sites:
• US Coast Guard Boating Safety Web Site: http://www.uscgboating.org/
• US Coast Guard Auxiliary: http://nws.cgaux.org/
• US Power Squadrons: http://www.usps.org
• Boat US: http://www.boatus.com

Perform safety checks and required maintenance.

Follow a regular schedule and ensure that all repairs are properly made.

Check for onboard safety equipment.

We suggest the following:
• Approved fire extinguishers
• Signal devices (flashlight, rockets or flares, flag, and a whistle or horn)
• Spare operating equipment (batteries, bulbs, fuses, etc.)
• Tools necessary for minor repairs
• An anchor and extra anchor line
• A manual bilge pump and extra drain plugs
• A supply of drinking water
• A transistor radio.
• Paddles or oars
• A spare propeller, spare thrust hubs, and an appropriate wrench
• A first aid kit and first aid instructions
• Waterproof storage containers
• A compass and appropriate maps or charts

Watch for signs of weather change.

Avoid foul weather and rough‑sea boating.

Tell someone where you are going and when you expect to return. Board cautiously.

Stop the engine whenever passengers are boarding, unloading, or are near the rear of the

boat. Operating in neutral is not sufficient.

Train emergency boat operators.

Instruct at least one other person onboard in the basics of starting and operating the power

package and boat handling in case the driver becomes disabled or falls overboard.

Do not overload your boat.

Содержание Axius 350 MAG





















































































































































Отзывы: