MerCruiser Axius 350 MAG Скачать руководство пользователя страница 4

Страница: 4 / 148

NOTICE

Indicates a situation which, if not avoided, could result in engine or major component

failure.

IMPORTANT: Identifies information essential to the successful completion of the task.

NOTE: Indicates information that helps in the understanding of a particular step or action.

WARNING

The operator (driver) is responsible for the correct and safe operation of the boat, the

equipment aboard and the safety of all occupants aboard. We strongly recommend that

the operator read this Operation, Maintenance and Warranty Manual and thoroughly

understand the operational instructions for the power package and all related accessories

before the boat is used.

WARNING

The engine exhaust from this product contains chemicals known to the state of California

to cause cancer, birth defects or other reproductive harm.

Содержание Axius 350 MAG





















































































































































Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды

MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды