background image

Section 5 - Maintenance 

Page  70

90-899883234   JANUARY  2008

Owner/Operator Responsibilities

It is the operator's responsibility to perform all safety checks, to ensure that all lubrication

and maintenance instructions are complied with for safe operation and to return the unit to

an authorized Mercury MerCruiser dealer for a periodic checkup.
Normal maintenance service and replacement parts are the responsibility of the owner/

operator and as such, are not considered defects in workmanship or material within the

terms of the warranty. Individual operating habits and usage contribute to the need for

maintenance service.
Proper maintenance and care of your power package will ensure optimum performance

and dependability and will keep your overall operating expenses at a minimum. See your

authorized Mercury MerCruiser dealer for service aids.

Dealer Responsibilities

In general, a dealer's responsibilities to the customer include predelivery inspection and

preparation such as:
• Ensure that the boat is properly equipped.
• Prior to delivery, make certain that the Mercury MerCruiser power package and other

equipment are in proper operating condition.

• Make all necessary adjustments for maximum efficiency.
• Familiarize the customer with the on‑board equipment.
• Explain and demonstrate the operation of the power package and boat.
• Provide you with a copy of a Predelivery Inspection Checklist.
• Your selling dealer should fill out the Warranty Registration Card completely and mail

it to the factory immediately upon sale of the new product.

Maintenance

!

 WARNING

Performing  service  or  maintenance  without  first  disconnecting  the  battery  can  cause

product  damage,  personal  injury,  or  death  due  to  fire,  explosion,  electrical  shock,  or

unexpected engine starting. Always disconnect the battery cables from the battery before

maintaining, servicing, installing, or removing engine or drive components.

!

 WARNING

Fuel  vapors  trapped  in  the  engine  compartment  may  be  an  irritant,  cause  difficulty

breathing,  or  may  ignite  resulting  in  a  fire  or  explosion.  Always  ventilate  the  engine

compartment before servicing the power package.

IMPORTANT:  Refer  to  the  maintenance  schedule  for  complete  listing  of  all  scheduled

maintenance to be performed. Whereas you can perform some items, others should be

performed  only  by  an  authorized  Mercury  MerCruiser  dealer.  Before  attempting

maintenance or repair procedures not covered in this manual, we recommend that you

purchase a Mercury MerCruiser service manual and read it thoroughly.

NOTE: Maintenance points are color coded for ease of identification. See the decal on

engine for identification.

Содержание Axius 350 MAG





















































































































































Отзывы: