MerCruiser Axius 350 MAG Скачать руководство пользователя страница 96

Страница: 96 / 148

Section 5 - Maintenance

Page 88

90-899883234 JANUARY 2008

1. Remove the PCV valve from the port valve cover.

mc71925-1

a -

PCV valve

b -

Hose

2. Disconnect the PCV valve from the hose and discard the valve.
3. Install a new PCV valve in the valve cover and reconnect the hose.
4. Ensure that the PCV valve is tightly seated in the valve cover.

Water‑Separating Fuel Filter (MPI)

Water‑Separating Fuel Filter

WARNING

Fuel is flammable and explosive. Ensure the key switch is off and the lanyard is positioned

so that the engine cannot start. Do not smoke or allow sources of spark or open flame in

the area while servicing. Keep the work area well ventilated and avoid prolonged

exposure to vapors. Always check for leaks before attempting to start the engine and

wipe up any spilled fuel immediately.

CAUTION

Failure to release pressure from the fuel system will result in fuel spraying out, which can

cause a fire or explosion. Allow the engine to cool completely and release all fuel pressure

before servicing any part of the fuel system. Always protect eyes and skin from

pressurized fuel and vapors.

Содержание Axius 350 MAG





















































































































































Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды

MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды