MerCruiser Axius 350 MAG Скачать руководство пользователя страница 89

Страница: 89 / 148

Section 5 - Maintenance

90-899883234 JANUARY 2008

Page 81

1. Check the gear lube level in the gear lube monitor. Keep the level within the

recommended operating range.

32539

a -

Gear lube monitor

b -

Typical closed cooled model

c -

Typical seawater cooled model

2. Inspect the lubricant condition. If any water is visible at the bottom of the gear lube

monitor, if water appears at the fill and drain plug hole, or if the gear lube appears

discolored, contact your authorized Mercury MerCruiser dealer immediately. These

conditions can indicate a water leak in the sterndrive.

Filling

IMPORTANT: If more than 59 mL (2 fl oz) of High Performance Gear Lubricant is required

to fill the monitor, a seal may be leaking. Damage to the sterndrive unit may occur due to

lack of lubrication. Contact your authorized Mercury MerCruiser dealer.
1. Remove the gear lube monitor cap.
2. Fill the monitor with the specified fluid so that the level is in the operating range. Do not

overfill.

7884

Shown removed for visual clarity

a -

Gear lube monitor cap

b -

Operating range (full) line

Tube Ref No.

Description

Where Used

Part No.

High Performance Gear

Lubricant

Gear lube monitor

92-858064K01

3. Ensure that the rubber gasket is inside the cap and install the cap. Do not overtighten.

NOTE: When filling the entire sterndrive unit refer to Changing.

Содержание Axius 350 MAG





















































































































































Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды

MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды