MerCruiser Axius 350 MAG Скачать руководство пользователя страница 104

Страница: 104 / 148

Section 5 - Maintenance

Page 96

90-899883234 JANUARY 2008

Serpentine Drive Belt

Checking

WARNING

Inspecting the belts with the engine running may cause serious injury or death. Turn off

the engine and remove the ignition key before adjusting tension or inspecting belts.

33283

a -

Alternator pulley

b -

Water circulating pump pulley

c -

Tensioner pulley and adjustment

stud

d -

Serpentine belt

e -

Steering pump pulley

f -

Crankshaft pulley

g -

Seawater pump pulley

h -

Idler pulley

1. Inspect the serpentine drive belt for the following:

•

Excessive wear

•

Cracks

NOTE: Minor, transverse cracks (across the belt width) may be acceptable. Longitudinal

cracks (in the direction of belt length) that join transverse cracks are not acceptable.

mc75130-1

•

Fraying

•

Glazed surfaces

•

Proper tension ‑ See

Replacing or Adjusting

for proper specifications.

Replacing or Adjusting

IMPORTANT: If a belt is to be reused, it should be installed in the same direction of rotation

as before.
1. Loosen the 16 mm (5/8 in.) locking nut on the adjustment stud.
2. Turn the adjustment stud and loosen the belt, if a new serpentine drive belt is required.

Remove the old belt and install a new belt onto the pulleys.

NOTE: Belt tension is measured on the belt at the location that has the longest distance

between two pulleys.

Содержание Axius 350 MAG





















































































































































Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды

MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды