MerCruiser Axius 350 MAG Скачать руководство пользователя страница 83

Страница: 83 / 148

Section 5 - Maintenance

90-899883234 JANUARY 2008

Page 75

1. Remove oil fill cap.

6065

IMPORTANT: Add the specified engine oil to bring the level up to, but not over, the full or

OK range mark on the dipstick.
2. Add the specified engine oil to bring the level up to, but not over, the full or OK range

mark on the dipstick. Recheck oil level.

3. Replace the fill cap.

Engine Model

Engine Oil Capacity

Fluid type

4.3L (262 cid) 3.8 liters (4 U.S. qt.)

Mercury/Quicksilver Synthetic Blend MerCruiser Engine Oil 25W‑40

5.0L (305 cid)

4.25 liters (4.5 U.S. qt.)

5.7L (350 cid)

Changing Oil and Filter

Refer to the Maintenance schedule for the change interval. Engine oil should be changed

before placing the boat in storage.
IMPORTANT: Change engine oil when the engine is warm from operation. Warm oil flows

more freely, carrying away more impurities. Use only recommended engine oil (refer to

Specifications).

EASY ENGINE OIL DRAIN SYSTEM

NOTE: Boat must be out of water to perform this procedure.

Содержание Axius 350 MAG





















































































































































Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды

MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды