MerCruiser Axius 350 MAG Скачать руководство пользователя страница 129

Страница: 129 / 148

Section 6 - Storage

90-899883234 JANUARY 2008

Page 121

6. Pump air into the system until both green indicators extend and water drains from both

sides of the engine. The port side will begin draining before the starboard side.

6124

6125

Closed Cooled Models

Seawater Cooled Models

a -

Blue drain plug location

b -

Blue air pump

c -

Air manifold

d -

Green indicators

7. Verify that water is draining from each opening. If not, use the

Three Point Manual

Drain System

instructions.

6133

a -

Port side drain location

b -

Starboard side drain location

8. Allow the system to drain for a minimum of five minutes. Pump air as necessary to keep

the green indicators extended.

9. Crank the engine over slightly with starter motor to purge any water trapped in the

seawater pump. Do not allow engine to start.

10. Remove the air pump from the air manifold and return it to the mounting bracket.
11. Mercury MerCruiser recommends leaving the drain system open while transporting the

boat or while performing other maintenance. This helps ensure that all water is drained.

Содержание Axius 350 MAG





















































































































































Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды

MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды