MerCruiser Axius 350 MAG Скачать руководство пользователя страница 67

Страница: 67 / 148

Section 3 - On The Water

90-899883234 JANUARY 2008

Page 59

7. If the ERC Handles are moved to neutral, Auto Heading turns off, a single beep sounds,

and the "STANDBY" light turns on. You cannot resume your course by pressing the

"RESUME" button.

31408

a -

"OFF" button

b -

Current heading

c -

Drive positions

d -

Engine RPM

Pressing the "AUTO HEADING" button causes VesselView to displays the "AUTO

HEADING" screen for three seconds. If the VesselView "AUTO HEADING" screen does

not appear, the "AUTO HEADING" screen needs to be activated in VesselView calibration.

Axius CAN still engages whether the screen appears or not.

NOTE: If you press the "AUTO HEADING" button a second time, the Axius CAN goes to

Standby mode and all lights other than "STANDBY" turn off.

DISENGAGE AUTO HEADING

1. Disengage the Auto Heading mode by any of the following actions:

•

Place the ERC levers for both engines in neutral.

•

Turn the steering wheel beyond the electronic detent.

•

Press the "AUTO HEADING" button on the Axius track pad. The "AUTO

HEADING" button LED light turns off.

RESUME

STANDBY

ACTIVE

AUTO

HEADING

TURN

32510

a -

Button LED light

b -

"AUTO HEADING" button

Содержание Axius 350 MAG





















































































































































Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды

MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды