MerCruiser Axius 350 MAG Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 148

background image

Section 5 - Maintenance

Page 106

90-899883234 JANUARY 2008

1. If flushing the cooling system with the boat in the water:

a.

Raise sterndrive to trailer position.

b.

Install the appropriate flushing attachment over the water inlet holes in the gear

housing.

c.

Lower sterndrive unit to full down (in) position.

2. If flushing the cooling system with the boat out of the water:

a.

Lower sterndrive to full down (in) position.

!

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the

water with a propeller installed. Before installing or removing a propeller, place the drive

unit in neutral and engage the lanyard stop switch to prevent the engine from starting.

Place a block of wood between the propeller blade and the anti‑ventilation plate.

b.

Remove propeller.

c.

Install the appropriate flushing attachment over the water inlet holes in the gear

housing.

3. Connect hose between flushing attachment and water source.
4. Close the seacock, if equipped, to prevent water from siphoning into the engine or boat.
5. Remove the seawater inlet hose from the seawater pump and plug the hose to prevent

water from siphoning into the engine or boat.

6147

6. Using a suitable adapter, connect the flushing hose from the water source to the water

inlet of the seawater pump.

NOTICE

Without sufficient cooling water, the engine, the water pump, and other components will

overheat and suffer damage. Provide a sufficient supply of water to the water inlets during

operation.

7. With sterndrive in normal operating position, open the water source fully.
8. Place the remote control in neutral idle speed position and start engine.

NOTICE

Operating the engine out of the water at high speeds creates suction, which can collapse

the water supply hose and overheat the engine. Do not operate the engine above 1400

RPM out of the water and without sufficient cooling water supply.

9. Slowly advance throttle until engine reaches 1300 RPM (+/‑100 RPM).

«
...
112
113
114
115
116
...
»

Содержание Axius 350 MAG





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350 MAG

Vanguard 540000 Series

Бренд: Briggs & Stratton Страницы: 32

E-8 DIESEL ENGINE

Бренд: M.T.H. Страницы: 36

Бренд: Cobra Страницы: 15

Бренд: VM Motori Страницы: 62

Бренд: Texas Equipment Страницы: 38

Бренд: Texas Equipment Страницы: 57

Бренд: Texas Equipment Страницы: 60

Бренд: YS Страницы: 2

Бренд: Motus Страницы: 32

Бренд: Briggs & Stratton Страницы: 11

Бренд: Black Bruin Страницы: 44

Allen-Bradley MP-Series

Бренд: Rockwell Automation Страницы: 68

Бренд: ZIEHL-ABEGG Страницы: 12

Бренд: ZIEHL-ABEGG Страницы: 20

Бренд: Honda Страницы: 72

Бренд: Hirth Страницы: 34

Бренд: YARDMAX Страницы: 24

Бренд: Robin America Страницы: 83

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды