MerCruiser Axius 350 MAG Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 148

background image

Section 7 - Troubleshooting

90-899883234 JANUARY 2008

Page 135

Electronic Remote Controls

Symptom

Remedy

The ERC (electronic

remote control) lever is too

hard or too easy to move

out of neutral detent.

Adjust detent tension. See

Section 2, Dual Handle Electronic Remote Control

with DTS Trackpad Features and Operation

.

The ERC lever has too

much or too little

resistance through its

range of motion.

Adjust the handle tension screw. See

Section 2, Dual Handle Electronic

Remote Control with DTS Trackpad Features and Operation

.

The ERC lever increases

engine RPM, but does not

engage gears and the boat

does not move.

Key off and key on.
Check the "Throttle Only" button on the DTS trackpad. Put the ERC levers in

neutral and push the button to disengage, if the light is on.
Engage gears manually. See

Section 3, Gear Engagement—Emergency

Procedure

.

Contact your authorized Mercury MerCruiser dealer.

The ERC lever controls the

engine and drive, but does

not reach wide open

throttle.

If the engine only reaches 50% of WOT, check the "DOCKING" button on the DTS

trackpad. Put the handles in neutral and push the button to disengage, if light is

on.
Check VesselView to see if cruise control enabled. Disable cruise control.
Check for damage to the propeller. Check VesselView for Guardian fault codes

that indicate reduced engine power. If found, contact your authorized Mercury

MerCruiser dealer to ask if the propellers need to be changed.

The ERC lever controls the

engine and drive, but does

not respond in a linear

manner.

Check the "TROLL" button on the DTS track pad. Put the handles in Neutral and

push the "TROLL" button to disengage, if light is on.

Check whether dock mode or cruise control are on. If on, turn off or disengage.

When one ERC lever is

moved, both engines

respond.

Check the "1 LEVER" button on the DTS track pad. If the light is on, put the

handles in neutral and push the "1 LEVER" button to disengage.

The ERC control, joystick,

and steering wheel do not

function.

Press "HELM" on DTS track pad to restore helm control. (Multiple helm boats

only.)

Steering System

Symptom

Remedy

The steering wheel steers the

boat, but operates without

resistance.

The starboard key switch is tuned off. Turn on the key.
Check and start the starboard engine.
Check if the starboard harness circuit breaker has tripped. Reset the circuit

breaker, if tripped.

Steering wheel does not steer

the boat.

Reduce speed and change to joystick for directional control.
Check steering fluid level and fill if necessary. See

Section 5—

Maintenance

.

Contact your authorized Mercury MerCruiser dealer.

Steering works, but the boat is

not as responsive.

Key off and key on.
Check and start the port engine.
Check the trim tab function.
Check the steering fluid level and fill if necessary. See

Section 5—

Maintenance

.

Contact your authorized Mercury MerCruiser dealer.

«
...
141
142
143
144
145
...
»

Содержание Axius 350 MAG





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350 MAG

Бренд: V2 Страницы: 20

Бренд: BAFANG Страницы: 12

Бренд: Club Car Страницы: 280

Бренд: Baratza Страницы: 5

Бренд: Generac Power Systems Страницы: 124

Бренд: Applied Motion Products Страницы: 2

Бренд: YARDMAX Страницы: 20

Бренд: Zenoah Страницы: 4

Бренд: Chicago Electric Страницы: 8

Бренд: Beta Страницы: 76

Бренд: Texas Equipment Страницы: 38

Бренд: Texas Equipment Страницы: 57

Бренд: Texas Equipment Страницы: 60

Бренд: Fagor Страницы: 174

Бренд: Yanmar Страницы: 316

Бренд: Barrus Страницы: 40

Бренд: Mitsubishi Heavy Industries Страницы: 156

Dexxo Pro 1000 RTS

Бренд: SOMFY Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды