MerCruiser Axius 350 MAG Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 148

background image

Section 6 - Storage

90-899883234 JANUARY 2008

Page 115

9. After draining, fill the seawater cooling system with propylene glycol mixed to the

manufacturer's recommendation for the lowest temperature to which the engine will be

exposed during freezing temperatures or extended storage.

10. Store the battery according to the manufacturer's instructions.

ENGINE AND FUEL SYSTEM PREPARATION

!

WARNING

Fuel is flammable and explosive. Ensure the key switch is off and the lanyard is positioned

so that the engine cannot start. Do not smoke or allow sources of spark or open flame in

the area while servicing. Keep the work area well ventilated and avoid prolonged

exposure to vapors. Always check for leaks before attempting to start the engine and

wipe up any spilled fuel immediately.

!

WARNING

Fuel vapors trapped in the engine compartment may be an irritant, cause difficulty

breathing, or may ignite resulting in a fire or explosion. Always ventilate the engine

compartment before servicing the power package.

1. In a 23 L (6 US gal) remote fuel tank mix:

a.

19 L (5 US gal) regular unleaded 87 octane (90 RON) gasoline

b.

1.89 L (2 US qt) Premium Plus 2‑Cycle TC‑W3 Outboard Oil

c.

150 ml (5 oz) Fuel System Treatment and Stabilizer or 30 ml (1 oz) Fuel System

Treatment and Stabilizer Concentrate

Tube Ref No.

Description

Where Used

Part No.

115

Premium Plus 2-cycle TC-W3

Outboard Oil

Fuel system

92-858026K01

124

Fuel System Treatment &

Stabilizer

Fuel system

858071K01

2. Allow the engine to cool down.
IMPORTANT: Immediately wipe up any fuel spills or sprays.
3. Close the fuel shut off valve, if equipped. Disconnect and plug the fuel inlet fitting if not

equipped with a fuel shut off valve.

4. Connect the remote fuel tank (with the fogging mixture) to the fuel inlet fitting.
IMPORTANT: Supply cooling water to the engine.
5. Start and operate the engine at 1300 RPM for 5 minutes.
6. Slowly return throttle to idle RPM and shut off the engine.
IMPORTANT: Ensure that some fogging mixture remains in the engine. Do not allow the

engines fuel system to become dry.
7. Replace the water separating fuel filter element. Refer to

Section 5

for proper

procedure.

8. Drain the engine seawater cooling system. Refer to

Section 5—Draining the

Seawater System

.

«
...
121
122
123
124
125
...
»

Содержание Axius 350 MAG





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350 MAG

Бренд: Hacker Страницы: 8

Бренд: Rail King Страницы: 46

Бренд: Subaru Страницы: 52

Бренд: DAF Страницы: 87

Бренд: MTU Страницы: 239

Бренд: Viessmann Страницы: 14

AUTOMATE MT01-2101-069002

Бренд: rollease acmeda Страницы: 30

Бренд: RAAMDECORATIE Страницы: 45

Бренд: Yanmar Страницы: 2

Бренд: Yanmar Страницы: 2

Бренд: Yanmar Страницы: 48

Бренд: MULTIPLEX modell Страницы: 6

Бренд: Honda Страницы: 156

Geareducer M1712

Бренд: Marley Страницы: 8

Бренд: Honda Страницы: 32

Бренд: Honda Страницы: 100

Бренд: Barrus Страницы: 100

P10-70-SSC Series

Бренд: LinMot Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды