MerCruiser Axius 350 MAG Скачать руководство пользователя страница 92

Страница: 92 / 148

Section 5 - Maintenance

Page 84

90-899883234 JANUARY 2008

2. Observe the oil level. Level must be between the "MIN" and "MAX" lines on the

reservoir.

7876

a -

Reservoir

b -

"MIN" and "MAX" lines

3. Fill as necessary with the specified fluid.

Tube Ref No.

Description

Where Used

Part No.

114

Power Trim and Steering Fluid

Power trim pump

92-858074K01

Filling

1. Remove the fill cap from the reservoir.

NOTE: Fill cap is vented.

2. Add lubricant to bring level to the within the "MIN" and "MAX" lines on the reservoir.

Tube Ref No.

Description

Where Used

Part No.

114

Power Trim and Steering Fluid

Power trim pump

92-858074K01

3. Install the cap.

Changing

Power trim fluid does not require changing unless it becomes contaminated with water or

debris. Contact your authorized Mercury MerCruiser dealer.

Battery

Refer to specific instructions and warnings accompanying your battery. If this information

is not available, observe the following precautions when handling a battery.

WARNING

Recharging a weak battery in the boat, or using jumper cables and a booster battery to

start the engine, can cause serious injury or product damage from fire or explosion.

Remove the battery from the boat and recharge in a ventilated area away from sparks or

flames.

WARNING

An operating or charging battery produces gas that can ignite and explode, spraying out

sulfuric acid, which can cause severe burns. Ventilate the area around the battery and

wear protective equipment when handling or servicing batteries.

Содержание Axius 350 MAG





















































































































































Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды

MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды