MerCruiser Axius 350 MAG Скачать руководство пользователя страница 70

Страница: 70 / 148

Section 3 - On The Water

Page 62

90-899883234 JANUARY 2008

3. Move the shift lever into the neutral position. The shift actuator is in the neutral position

when the shift lever is straight up and the shift interrupt switch is fully engaged.

32243

a -

Harness

b -

Shift lever

c -

Shift lever in neutral position

d -

Shift lever in forward position

e -

Shift lever in reverse position

f -

Gear position indicator switch

4. With the drive in neutral, place the ERC into the neutral (idle) position.
5. Reset the lanyard.

WARNING

A spinning propeller, a moving boat, or any solid device attached to the boat can cause

serious injury or death to swimmers. Stop the engine immediately whenever anyone in

the water is near your boat.

6. Ensure that no one is in the water near the boat, then start the engine.
7. With the engine running at idle speed, the drive can be shifted into gear and out of gear

by manually moving the shift lever.

NOTE: Engine speed will be limited to 1000–1200 RPM while operating in emergency shift

override. The Auto Heading feature using the Axius track pad will still function but is limited

to this reduced RPM setting.

IMPORTANT: The boat's stopping distance increases during manual gear engagement

operation.

Содержание Axius 350 MAG





















































































































































Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды

MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды