MerCruiser Axius 350 MAG Скачать руководство пользователя страница 133

Страница: 133 / 148

Section 6 - Storage

90-899883234 JANUARY 2008

Page 125

3. To properly vent the cooling system, remove the blue drain plug from the side of the

thermostat housing within 30 seconds.

6139

a -

Blue drain plug location

4. Remove the two blue drain plugs from the seawater pickup pump (front, starboard side).

6140

a -

Blue drain plugs

5. Verify that water is draining from each opening.
6. Allow the system to drain for a minimum of five minutes. We recommend leaving the

drain system open while transporting the boat or performing other maintenance to

ensure that all water is drained.

7. Crank the engine over slightly with starter motor to purge any water trapped in the

seawater pickup pump. Do not allow the engine to start.

8. Before launching the boat or starting the engine, close the drain system by installing

the four blue drain plugs.

9. Open the seacock, if equipped, or unplug and reconnect the water inlet hose prior to

operating the engine.

BOAT OUT OF THE WATER

NOTE: Use this procedure if your engine is not equipped with an air‑actuated single‑point

drain system or if the single‑point drain system fails.

1. Place the boat on a level surface to ensure complete draining of the system.

Содержание Axius 350 MAG





















































































































































Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды

MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды