MerCruiser Axius 350 MAG Скачать руководство пользователя страница 95

Страница: 95 / 148

Section 5 - Maintenance

90-899883234 JANUARY 2008

Page 87

mc71925-1

a -

PCV valve

b -

Hose

3. If inspecting the valve with the engine stopped:

Disconnect the PCV valve from the hose.

Shake the PCV valve. If you hear a metallic rattle, the valve is functional. If you

do not hear the rattle, replace the valve.

Install the valve onto the hose.

4. If inspecting the valve with the engine running:

Leave the hose connected to the PCV valve.

Start the engine. You may hear the sound of suction through the PCV valve.

Place a small sheet of card stock or heavy paper near the open end of the PCV

valve. If the valve is working, the manifold vacuum will suck the paper against the

open end of the valve.

Stop the engine. If the paper was not drawn onto the open end of the valve, check

the hose connection and for vacuum leaks in the hose. If no leaks are present,

replace the PCV valve.

5. Install the PCV valve in the valve cover and reconnect the hose, if not connected

already.

6. Ensure that the PCV valve is tightly seated in the valve cover.

Replacement

IMPORTANT: Use only Mercury MerCruiser replacement parts to ensure compliance with

emission regulations.

Содержание Axius 350 MAG





















































































































































Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды

MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды