MerCruiser Axius 350 MAG Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 148

background image

Section 1 - Warranty

Page 14

90-899883234 JANUARY 2008

5. Exhaust System.

a.

Exhaust manifold

b.

Exhaust elbow

c.

Intermediate exhaust elbow

d.

Lower exhaust pipe

e.

Tailpipe

f.

Exhaust valve

6. Miscellaneous Items Used in Above Systems

a.

Hoses, clamps, fittings, tubing, sealing gaskets or devices, and mounting

hardware

b.

Pulleys, belts, and idlers

c.

Vacuum, temperature, check and time sensitive valves and switches

d.

Electronic controls.

Disclaimers And Limitations

DISCLAIMERS AND LIMITATIONS
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE  EXPRESSLY  DISCLAIMED.  TO  THE  EXTENT  THAT  THEY  CANNOT  BE  DISCLAIMED,  THE
IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE LIFE OF THE EXPRESS WARRANTY.
INCIDENTAL AND CONSEQUENTIAL DAMAGES ARE EXCLUDED FROM COVERAGE UNDER THIS
WARRANTY. SOME STATES/COUNTRIES DO NOT ALLOW FOR THE DISCLAIMERS, LIMITATIONS
AND  EXCLUSIONS  IDENTIFIED  ABOVE.  AS  A  RESULT,  THEY  MAY  NOT  APPLY  TO  YOU.  THIS
WARRANTY  GIVES  YOU  SPECIFIC  LEGAL  RIGHTS,  AND  YOU  MAY  ALSO  HAVE  OTHER  LEGAL
RIGHTS WHICH VARY FROM STATE TO STATE AND COUNTRY TO COUNTRY.

If you have any questions regarding your warranty rights and responsibilities, refer to

Owner Service Assistance for contact information.

California Emission Control Warranty Statement

Your Warranty Rights and Obligations

The California Air Resources Board is pleased to explain the emission control system
warranty on your 2003 model year

1.

and later inboard or sterndrive engine. In California,

new inboard and sterndrive engines must be designed, built and equipped to meet the

State's stringent anti‑smog standards. Mercury Marine must warrant the emission control

system on your inboard or sterndrive engine for the periods of time listed below provided

there has been no abuse, neglect or improper maintenance of your inboard or sterndrive

engine.
Your emission control system may include parts such as the carburetor or fuel injection

system, the ignition system, and catalytic converter. Also included may be hoses, belts,

connectors and other emission‑related assemblies.
Where a warrantable condition exists, Mercury Marine will repair your inboard or sterndrive

engine at no cost to you; including diagnosis, parts and labor.

Manufacturer's Warranty Coverage

For 2003‑2008 spark‑ignition inboard and sterndrive marine engines: Select emission
control parts from model year

1.

2003‑2008 inboard and sterndrive engines are warranted

for 2 years. If any emission‑related part on your engine is defective under warranty, the

part will be repaired or replaced by Mercury Marine.

1. Mercury Marine does not establish model years for the Mercury MerCruiser product line. In order to comply with CARB warranty

regulations, and for that limited purpose only, model year shall have the same meaning as calendar year. As an example, 2003

model year products refers to products manufactured during calendar year 2003.

«
...
20
21
22
23
24
...
»

Содержание Axius 350 MAG





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350 MAG

Бренд: Yamaha Страницы: 7

3T-MOTORS 3T45-20

Бренд: 3T-Components Страницы: 24

Бренд: GR Страницы: 8

Command Pro EFI ECH940

Бренд: Kohler Страницы: 8

Courage PRO SV810

Бренд: Kohler Страницы: 20

KDI 3404TCR-SCR

Бренд: Kohler Страницы: 64

Бренд: Kohler Страницы: 88

Бренд: Kohler Страницы: 334

Бренд: Lombardini Страницы: 92

Бренд: Toro Страницы: 96

Бренд: Lister Petter Страницы: 24

Бренд: Motion Страницы: 92

Бренд: Honda Страницы: 162

Бренд: Briggs & Stratton Страницы: 11

Бренд: Iveco Страницы: 74

Бренд: Stiga Страницы: 88

Бренд: Briggs & Stratton Страницы: 9

Бренд: Vetus Страницы: 134

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды