MerCruiser Axius 350 MAG Скачать руководство пользователя страница 137

Страница: 137 / 148

Section 6 - Storage

90-899883234 JANUARY 2008

Page 129

3. For additional assurance against freezing and rust, after draining, fill the cooling system

with propylene glycol mixed to the manufacturer's recommendation to protect engine

to the lowest temperature to which it will be exposed during freezing temperatures or

extended storage

IMPORTANT: Mercury MerCruiser requires that propylene glycol antifreeze, mixed to the

manufacturers instructions, be used in the seawater section of the cooling system for

freezing temperatures or extended storage. Make sure that the propylene glycol antifreeze

contains a rust inhibitor and is recommended for use in marine engines. Be certain to follow

the propylene glycol manufacturer's recommendations.

Battery Storage

Whenever the battery will be stored for an extended period of time, be sure the cells are

full of water and the battery is fully charged and in good operating condition. It should be

clean and free of leaks. Follow the battery manufacturer's instructions for storage.

Power Package Recommissioning

1. Ensure that all cooling system hoses are connected properly and hose clamps are tight.

CAUTION

Disconnecting or connecting the battery cables in the incorrect order can cause injury

from electrical shock or can damage the electrical system. Always disconnect the

negative (‑) battery cable first and connect it last.

2. Install a fully charged battery. Clean the battery cable clamps and terminals and

reconnect cables. Tighten each cable clamp securely when connecting.

3. Coat the terminal connections with a battery terminal anti‑corrosion agent.
4. Perform all the checks in the before starting column of the

Operation Chart

NOTICE

Without sufficient cooling water, the engine, the water pump, and other components will

overheat and suffer damage. Provide a sufficient supply of water to the water inlets during

operation.

5. Start the engine and closely observe instrumentation to ensure that all systems are

functioning correctly.

6. Carefully inspect the engine for fuel, oil, fluid, water and exhaust leaks.
7. Inspect the steering system, shift and throttle control for proper operation.

Содержание Axius 350 MAG





















































































































































Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды

MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды