MerCruiser Axius 350 MAG Скачать руководство пользователя страница 34

Страница: 34 / 148

Section 2 - Getting to Know Your Power Package

Page 26

90-899883234 JANUARY 2008

We recommend that you drive carefully until you have a chance to explore the Axius

system's handling characteristics and boat's responses in an open area clear of

obstructions or other boat traffic. The initial steering setting of two turns lock‑to‑lock provids

a fast steering response. Maneuvers at speed can be more abrupt than expected. The

distributor can adjust the number of turns, if desired.

Dual‑Handle Electronic Remote Control (ERC) with DTS Trackpad Features and

Operation

OPERATION

The electronic remote control (ERC) handle operates the shift and throttle. Push the ERC

handles handle forward from neutral to the first detent for forward gear. Continue pushing

the ERC handle forward to increase speed. Pull the ERC handle from the forward position

to the neutral position to decrease speed and eventually stop. Pull the ERC handle back

from neutral to the first detent for reverse gear. Continue pulling the handle back to increase

speed.

NOTE: When using the joystick, the computer moves the sterndrive in and out of gear

even though the ERC handles remain in neutral.

28086

Typical ERC handles

a -

Neutral

b -

Forward

c -

Reverse

d -

Bow of boat

ADJUSTMENT

The amount of force needed to move the ERC handles and to move the ERC handles

through the detentes is adjustable to help prevent unwanted motion of the handle in rough

water.
To adjust ERC handle tension:
1. Remove the port side cover for port lever adjustment, and starboard side cover for

starboard lever adjustment.

2. Turn the screw clockwise to increase tension on the control handle and

counter‑clockwise to decrease tension.

3. Adjust to tension desired.
To adjust ERC handle detent tension:
1. Remove the port side cover for port lever adjustment, and starboard side cover for

starboard lever adjustment.

Содержание Axius 350 MAG





















































































































































Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды

MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды