MerCruiser Axius 350 MAG Скачать руководство пользователя страница 38

Страница: 38 / 148

Section 2 - Getting to Know Your Power Package

Page 30

90-899883234 JANUARY 2008

NOTE: In an emergency, when the engine must be operated and the cause for the high

current draw (overload) cannot be located and corrected, turn off or disconnect all

accessories connected to the engine and instrumentation wiring. Reset the circuit breaker.

If the breaker remains open, the electrical overload has not been eliminated. Further

checks must be made on the electrical system. Contact your authorized dealer.

1. A circuit breaker protects the engine wiring harness and the instrumentation power

lead. Test the circuit breaker by pushing the red button. To reset the breaker, push the

yellow lever back into the housing.

22529

a -

Yellow lever—shown tripped

b -

Red test button

2. A 90 amp fuse is located on the large post of the starter solenoid. This fuse protects

the engine wiring harness if an electrical overload or a reversed battery condition

occurs.

mc74907-1

3. Four fuses are located on the port side of the engine. These fuses protect various

Electronic Fuel Injection (EFI) circuits.

mc77602-1

Содержание Axius 350 MAG





















































































































































Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды

MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание Axius 350 MAG

Отзывы:

Похожие инструкции для Axius 350 MAG

Бренды по названию

Популярные бренды