MerCruiser Axius 350 MAG Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 148

background image

Section 3 - On The Water

Page 52

90-899883234 JANUARY 2008

Item Control

Function

a "NEUTRAL" lights

Illuminate when the transmission is in the neutral gear position. The

lights flash when the engine is in throttle only mode.

b Not used

None

c "TRANSFER"

Allows boat control to be transferred to a different helm. Refer to Helm

Transfer.

d "DOCK"

Reduces throttle capacity to approximately 50% of normal throttle.

e "THROTTLE ONLY"

Allows the boat operator to increase engine RPM for warm‑up without

shifting the transmission into gear.

f

"1 LEVER"

Enables the throttle and shift functions of both engines to be

controlled by the port lever.

g "SYNC"

Turns off or on the auto‑synchronization feature. Refer to

Synchronizing Engines.

h "+" (increase) and "–" (decrease) Increases and decreases settings for various functions, like cruise

control speed.

NOTE: Not all functions may be active.

DOCK

Dock mode reduces the RPM throughout the range by 50%. Dock mode also reduces

available power when the joystick is enabled, allowing finer control of engine power in close

quarter situations.

31464

"DOCK" button

To engage Dock mode:
1. Place both ERC levers in neutral.
2. Press the "DOCK" button located on the DTS Trackpad attached to the ERC levers.
3. The "DOCK" button light turns on.
4. Place either ERC lever into gear.
5. The engines raise the RPM at a proportionally lower RPM for the ERC lever position,

and with half the usually available power.

To disengage Dock mode:

NOTE: Dock only disengages with the levers in a detent.

1. Bring both ERC levers to any detent.
2. Press the "DOCK" button. The "DOCK" button light turns off.

«
...
58
59
60
61
62
...
»

Содержание Axius 350 MAG





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350 MAG

Бренд: BAFANG Страницы: 12

Бренд: Jacobsen Страницы: 103

Бренд: Kohler Страницы: 116

Jeep Six-Cylinder

Бренд: Golen Страницы: 11

Бренд: Sachs Страницы: 42

High-Power RMS-PLUS 54/1706

Бренд: Aerotech Страницы: 2

RMS 98/10240 BLACK MAX

Бренд: Aerotech Страницы: 2

Бренд: Petter Страницы: 58

Бренд: Albin Страницы: 31

Бренд: PST Jets Страницы: 44

2005 250 EXC-F SIX DAYS

Бренд: KTM Страницы: 151

Бренд: Vetus Страницы: 80

Бренд: Jacobsen Страницы: 104

Бренд: IAME Страницы: 28

Бренд: TOSO Страницы: 10

Бренд: Zenoah Страницы: 4

Бренд: Saito Страницы: 28

Бренд: Orientalmotor Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды