MerCruiser Axius 350 MAG Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 148

background image

Section 3 - On The Water

Page 42

90-899883234 JANUARY 2008

Use extreme caution when operating in shallow water or where underwater objects are

known to be present. No impact protection is provided in reverse; use extreme care to

prevent striking submerged objects while operating in reverse.
IMPORTANT: Impact protection system cannot be designed to ensure total protection from

impact damage under all conditions.

Trailering the Boat

IMPORTANT: The Axius system can not steer without the engines running. If your vessel

requires a specific steering angle upon trailering, obtain that angle prior to keying down the

engines.
The boat can be trailered with the sterndrive unit in the up(out) or down(in) position. Ensure

adequate clearance between the road and sterndrive when transporting. If you require

additional clearance, place the sterndrive unit in full trailer position and support it with an

optional trailer kit, which is available from your authorized Mercury MerCruiser dealer.

Conditions Affecting Operation

Weight Distribution (Passengers and Gear) Inside the Boat

Shifting weight to rear (stern):
• Generally increases speed and engine RPM
• Causes bow to bounce in choppy water
• Increases danger of following wave splashing into the boat when coming off plane
• At extremes, can cause the boat to porpoise
Shifting weight to front (bow):
• Improves ease of planing
• Improves rough water ride
• At extremes, can cause the boat to veer back and forth (bow steer)

The Bottom of the Boat

To maintain maximum speed, the boat bottom should be:
• Clean, free of barnacles and marine growth
• Free of distortion; nearly flat where it contacts the water
• Straight and smooth, fore and aft
Marine vegetation may accumulate when the boat is docked. This growth must be removed

before operation; it may clog the water inlets and cause the engine to overheat.

Cavitation

Cavitation occurs when water flow cannot follow the contour of a fast‑moving underwater

object such as a gear housing or a propeller. Cavitation increases propeller speed while

reducing boat speed. Cavitation can seriously erode the surface of the gear housing or the

propeller. Common causes of cavitation are:
• Weeds or other debris snagged on the propeller
• Bent propeller blade
• Raised burrs or sharp edges on the propeller

Ventilation

Ventilation is caused by surface air or exhaust gases that are introduced around the

propeller resulting in propeller speed‑up and a reduction in boat speed. Air bubbles strike

the propeller blade and cause erosion of the blade surface. If allowed to continue, eventual

blade failure (breakage) will occur. Excessive ventilation is usually caused by:

«
...
48
49
50
51
52
...
»

Содержание Axius 350 MAG





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350 MAG

Бренд: jcb Страницы: 122

Бренд: Quectel Страницы: 71

Era-Era Star Head EMPC

Бренд: Nice Страницы: 2

Бренд: Bosch Страницы: 20

Rexroth Hagglunds CA 10

Бренд: Bosch Страницы: 53

Бренд: Bosch Страницы: 60

Бренд: Bosch Страницы: 74

Rexroth Hagglunds CA 100

Бренд: Bosch Страницы: 76

Rexroth 70 Series

Бренд: Bosch Страницы: 56

Rexroth IndraDyn T

Бренд: Bosch Страницы: 76

Rexroth A10VER 52 Series

Бренд: Bosch Страницы: 56

Бренд: Bosch Страницы: 48

Бренд: Bosch Страницы: 114

Бренд: Bosch Страницы: 72

Rexroth A6VM series 71

Бренд: Bosch Страницы: 76

Rexroth Hagglunds VI 44 Series

Бренд: Bosch Страницы: 68

Rexroth IndraDyn S MS2N

Бренд: Bosch Страницы: 118

Бренд: Bosch Страницы: 206

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды