MerCruiser Axius 350 MAG Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 148

background image

Section 2 - Getting to Know Your Power Package

Page 32

90-899883234 JANUARY 2008

6. The Quicksilver MerCathode system has a 20 amp in‑line fuse in the wire which

connects to the positive (+) terminal on controller. If the fuse is blown, the system will

not operate resulting in a loss of corrosion protection.

mc79977

Warning Horn Signals

Most faults will cause the warning horn circuit to activate. How the warning horn activates

depends on how serious the problem is. There are four warning horn states:
• Caution ‑ horn signal varies with product line and calibration. Minimal guardian.
• Warning ‑ horn signal varies with product line and calibration.
• Severe ‑ horn is beeping constantly.
• Critical ‑ horn is beeping constantly and guardian will be at forced idle.
In addition, depending on the gauge package, there will be warning icons and fault

messages on the dash mounted gauges.

Audio Warning System

Your Mercury MerCruiser power package may be equipped with an Audio Warning System.

The Audio Warning System will not protect the engine from damage. It is designed to warn

the operator that a problem has occurred.
The audio warning system will sound with a continuous horn:
• Engine oil pressure is too low
• Engine temperature is too hot
• Seawater pressure is too low
The audio warning system will sound with an intermittent beeping:
• The sterndrive oil level is too low
• Engine guardian activates
• A sensor failure is detected
• A communication failure within a CAN system occurs

NOTICE

A continuous horn indicates a critical fault. Operating the engine during a critical fault can

damage components. If the warning horn emits a continuous beep, do not operate the

engine unless avoiding a hazardous situation.

If the alarm sounds, stop the engine immediately. Investigate the cause and correct it, if

possible. If you cannot determine the cause, contact your authorized Mercury MerCruiser

dealer.

TESTING THE AUDIO WARNING SYSTEM

1. Turn the ignition switch to the "ON" position without cranking the engine.

«
...
38
39
40
41
42
...
»

Содержание Axius 350 MAG





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350 MAG

Бренд: ABB Страницы: 8

Бренд: Garmin Страницы: 16

Бренд: Subaru Страницы: 52

Бренд: RenewAire Страницы: 28

Бренд: GGP Страницы: 56

Torqmotor TF Series

Бренд: Parker Страницы: 44

AstroTrack 21047

Бренд: ORION TELESCOPES & BINOCULARS Страницы: 2

Бренд: IMS Страницы: 6

Бренд: MINN KOTA Страницы: 42

EM-PMI540-T1500

Бренд: Danfoss Страницы: 76

Бренд: Sears Страницы: 12

Бренд: Iveco Motors Страницы: 60

Бренд: Iveco Страницы: 206

Sterndrive TDI 3.0L

Бренд: MerCruiser Страницы: 119

Бренд: VM Страницы: 108

Бренд: aFe Power Страницы: 16

BEVELMASTER 204B

Бренд: TRI tool Страницы: 46

Бренд: Krick Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды