Meco Pellematic PES 12-20 Скачать руководство пользователя страница 78

Страница: 78 / 102

Malfunctions

suction fan unplugged

► connect up suction fan

fuse on suction fan
defective

► replace fuse

storage room auger motor
unplugged

► connect up storage room motor

Table 13.11 Motors

Display:

Burner motor

Description:

Burner motor malfunction

Cause and Remedy:

motor unplugged

► plug in motor, check cable connections

motorpower too high

► too low adjusted, motor sticks or is defective

motorpower too low

► too high adjusted, motor sticks or is defective

motor is sticking

remove the pellets from the burner auger, make the
motor easy-running

motor defective

► replace motor

Display:

Suction turb

Description:

Suction turbine malfunction

Cause and Remedy:

motor unplugged

► plug in motor, check cable connections

motor defect

► replace motor

fuse –F1 of the suction
circuit board is defective

► replace fuse –F1of the suction of the suction circuit

board

fire protection system does
not reach CLOSE limit
switch

►

check whether ball valve is jammed, check ball valve
throughway to see if foreign objects are preventing
it from closing

Display:

Fuel trans sys M

Description:

Storage room auger 1 motor malfunction

Cause and Remedy:

motor unplugged

► plug in motor, check cable connections

motor is jammed

► remove pellets from auger and make sure auger

rotates freely

fuse –F2 of the suction
circuit board is defective

► replace fuse –F2 of the suction circuit board

motor defect

► replace motor

fuse defect

► replace fuse

Display:

Ignition

Description:

Ignitions stick malfunction

Cause and Remedy:

ignition stick unplugged

► plug in ignition stick, check cable connections

power too high

► too low adjusted, ignition stick is defective

power too low

► too high adjusted, ignition stick is defective

motor defective

► check the resistance to see if the ignition stick is

defective or not
(0, 400 and ~ = ignition stick is defective, all other
values = ignition stick is not defective), replace ignition
stick

Display:

Burner fan

Description:

Burner fan malfunction

Cause and Remedy:

motor unplugged

► plug in motor, check cable connections

Installation Manual PES 36–56

PE 3671 USA 2.3

Содержание Pellematic PES 12-20







































































































Результаты поиска

Содержание Pellematic PES 12-20

Отзывы:

Похожие инструкции для Pellematic PES 12-20

Бренды по названию

Популярные бренды

Meco Pellematic PES 12-20, Руководство по установке

Результаты поиска

Содержание Pellematic PES 12-20

Отзывы:

Похожие инструкции для Pellematic PES 12-20

Бренды по названию

Популярные бренды