Meco Pellematic PES 12-20 Скачать руководство пользователя страница 76

Страница: 76 / 102

Malfunctions

Display:

UP sh-c

Description:

Negative draft input short-circuit, measuring circuit from negative draft measurement
is shorted out

Cause and Remedy:

signal wrong

► check polarity and signal (0-10V)

signal cable defect

► replace sensor

signal input defect

► change CMP PLC

signal too high

► signal above 10V

Table 13.5 Analog input 2

Display:

An. input open

Description:

Analog input 2 open, measuring circuit from analog input open

Cause and Remedy:

signal incorrect

► check polarity and signal (0-10V)

signal cable defect

► repair/replace cable

signal input defect

► change CMP PLC

signal too low

► signal below 0V

Display:

An. input 2 sh-c

Description:

Analog input 2 short-circuit, measuring circuit from analog input is shorted out

Cause and Remedy:

signal incorrect

► check polarity and signal (0-10V)

signal cable defect

► repair/replace cable

signal input defect

► change CMP PLC

signal too high

► signal above 10V

Table 13.6 Controller sensor

Display:

Control S fr

Description:

Controller sensor fracture, control system sensor on boiler control system is used as
reference for combustion chamber sensor

Cause and Remedy:

signal input defect

► change CMP PLC

temperature too high

► temperature above 158°F

Display:

Control S sh-c

Description:

Controller sensor short-circuit, control system sensor on boiler control system is used as
reference for combustion chamber sensor

Cause and Remedy:

signal input defect

► change CMP PLC

temperature too low

► temperature below 14°F

Table 13.7 Ignition and flame supervision

Display:

Ignition malf

Description:

Flue gas minimum temperature not reached during ignition phase

Cause and Remedy:

no pellets available

► fill up with pellets

ignition electrode defect

► check ignition electrode (approx. 200Ω) replace if

required

ignition nozzle blocked

► clean burner plate and ignition tube

flue gas sensor
contaminated

► clean flue gas sensor and flue gas tube

flue gas sensor is not in flue
gas tube

► insert flue gas sensor into flue gas tube

Installation Manual PES 36–56

PE 3671 USA 2.3

Содержание Pellematic PES 12-20







































































































Результаты поиска

Содержание Pellematic PES 12-20

Отзывы:

Похожие инструкции для Pellematic PES 12-20

Бренды по названию

Популярные бренды

Meco Pellematic PES 12-20, Руководство по установке

Результаты поиска

Содержание Pellematic PES 12-20

Отзывы:

Похожие инструкции для Pellematic PES 12-20

Бренды по названию

Популярные бренды